Wednesday, June26, 2019 L-36.com

Harken 6066 Deck Organizer Instruction Sheet



Note:

This is the new page for displaying documents. It allows documents to display on devices without pdf viewers specifically mobile devices, a new Google requirement. Note also that some documents have blank pages. Just click on "Next Page" if that happens.
Previous Page    Next Page Go to page number Note: Page number may not agree with index page numbers


Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.

AdobeUCSAdobeUCSAdobeUCSYou must install the enclosed clear plastic washers between the stainless steel washers and the aluminum top plate to prevent dissimilar metal corrosion Failure to install washers will void Harken warrantyInstall Clear Plastic Washer IsolatorsTel 2626913320 Fax 2627015780Web wwwharkencom Email harkenharkencomStrictly follow all instructions to avoid an accident damage to your vessel personal injury or death See wwwharkencommanuals Use stainless steel fasteners in all mounting holes using backing plates washers and locknuts Deck or mounting surface must solid designed for block load Consult with builderYou must install the enclosed clear plastic washers between the stainless steel washers and the aluminum top plate to prevent dissimilar metal corrosion Failure to install washers will void Harken warrantyInstall Clear Plastic Washer IsolatorsTel 2626913320 Fax 2627015780Web wwwharkencom Email harkenharkencomStrictly follow all instructions to avoid an accident damage to your vessel personal injury or death See wwwharkencommanuals Use stainless steel fasteners in all mounting holes using backing plates washers and locknuts Deck or mounting surface must solid designed for block load Consult with builderYou must install the enclosed clear plastic washers between the stainless steel washers and the aluminum top plate to prevent dissimilar metal corrosion Failure to install washers will void Harken warrantyInstall Clear Plastic Washer IsolatorsTel 2626913320 Fax 2627015780Web wwwharkencom Email harkenharkencomStrictly follow all instructions to avoid an accident damage to your vessel personal injury or death See wwwharkencommanuals You must install the enclosed clear plastic washers between the stainless steel washers and the aluminum top plate to prevent dissimilar metal corrosion Failure to install washers will void Harken warrantyYou must install the enclosed clear plastic washers between the stainless steel washers and the aluminum top plate to prevent dissimilar metal corrosion Failure to install washers will void Harken warrantyInstall Clear Plastic Washer IsolatorsTel 2626913320 Fax 2627015780Web wwwharkencom Email harkenharkencomStrictly follow all instructions to avoid an accident damage to your vessel personal injury or death See wwwharkencommanuals You must install the enclosed clear plastic washers between the stainless steel washers and the aluminum top plate to prevent dissimilar metal corrosion Failure to install washers will void Harken warrantyXjyAirhGs8zzz9vwa2TKMkRb7tY0W1688ZI8l78wWxonpiiif87zEBQYzb7dKYwsmA1UyBKXw74AOgvvn3P7v8cOfUTQkGiQ QR iRyZzb5q6dO k8tS X dX  X Z e Z dk2VM29mTgIuP  h 9wcAdobeUCScwa2w7zEBQYww9YZDPUTQUTQTighten bolts only  to remove play between Overtightening will permanently damage organizer and cause sheaves to bind Tighten wrist tight 10 ftlb14 NmDO NOT OVERTIGHTEN227ORGANIZERSFOOTBLOCKSFor additional safety maintenance and warranty information see wwwharkencomWarrantyHarken equipment requires minimal maintenance but some is required to give the best service and to comply with Harkens limited warrantyIt is important to keep equipment clean by frequent flushing with fresh water In corrosive atmospheres stainless parts may show discoloration around holes rivets and Flush blocks thoroughly with fresh water Periodically disassemble the blocks and clean with detergent and fresh water Lubrication is not requiredClear plastic washers should always be used between stainless fasteners and aluminum sideplates Stainless fasteners which pass through aluminum blocks should be coated Locking nuts should not be used after being removed three times When replacing IMPORTANTresult in discoloration of part and is not covered under the Harken warrantyTighten bolts only  to remove play between Overtightening will permanently damage organizer and cause sheaves to bind Tighten wrist tight 10 ftlb14 NmDO NOT OVERTIGHTEN227ORGANIZERSFOOTBLOCKSFor additional safety maintenance and warranty information see wwwharkencomWarrantyHarken equipment requires minimal maintenance but some is required to give the best service and to comply with Harkens limited warrantyIt is important to keep equipment clean by frequent flushing with fresh water In corrosive atmospheres stainless parts may show discoloration around holes rivets and Flush blocks thoroughly with fresh water Periodically disassemble the blocks and clean with detergent and fresh water Lubrication is not requiredClear plastic washers should always be used between stainless fasteners and aluminum sideplates Stainless fasteners which pass through aluminum blocks should be coated Locking nuts should not be used after being removed three times When replacing IMPORTANTresult in discoloration of part and is not covered under the Harken warrantyTighten bolts only  to remove play between Overtightening will permanently damage organizer and cause sheaves to bind Tighten wrist tight 10 ftlb14 NmDO NOT OVERTIGHTEN227ORGANIZERSFOOTBLOCKSFor additional safety maintenance and warranty information see wwwharkencomWarrantyHarken equipment requires minimal maintenance but some is required to give the best service and to comply with Harkens limited warrantyIt is important to keep equipment clean by frequent flushing with fresh water In corrosive atmospheres stainless parts may show discoloration around holes rivets and Flush blocks thoroughly with fresh water Periodically disassemble the blocks and clean with detergent and fresh water Lubrication is not requiredClear plastic washers should always be used between stainless fasteners and aluminum sideplates Stainless fasteners which pass through aluminum blocks should be coated Locking nuts should not be used after being removed three times When replacing IMPORTANTresult in discoloration of part and is not covered under the Harken warrantyTighten bolts only  to remove play between Overtightening will permanently damage organizer and cause sheaves to bind Tighten wrist tight 10 ftlb14 NmDO NOT OVERTIGHTEN227ORGANIZERSFOOTBLOCKSFor additional safety maintenance and warranty information see wwwharkencomWarrantyHarken equipment requires minimal maintenance but some is required to give the best service and to comply with Harkens limited warrantyIt is important to keep equipment clean by frequent flushing with fresh water In corrosive atmospheres stainless parts may show discoloration around holes rivets and Flush blocks thoroughly with fresh water Periodically disassemble the blocks and clean with detergent and fresh water Lubrication is not requiredClear plastic washers should always be used between stainless fasteners and aluminum sideplates Stainless fasteners which pass through aluminum blocks should be coated Locking nuts should not be used after being removed three times When replacing IMPORTANTresult in discoloration of part and is not covered under the Harken warrantyAdobeUCS

Ad by Google

Disclaimer:
The information on this web site has not been checked for accuracy. It is for entertainment purposes only and should be independently verified before using for any other reason. There are five sources. 1) Documents and manuals from a variety of sources. These have not been checked for accuracy and in many cases have not even been read by anyone associated with L-36.com. I have no idea of they are useful or accurate, I leave that to the reader. 2) Articles others have written and submitted. If you have questions on these, please contact the author. 3) Articles that represent my personal opinions. These are intended to promote thought and for entertainment. These are not intended to be fact, they are my opinions. 4) Small programs that generate result presented on a web page. Like any computer program, these may and in some cases do have errors. Almost all of these also make simplifying assumptions so they are not totally accurate even if there are no errors. Please verify all results. 5) Weather information is from numerious of sources and is presented automatically. It is not checked for accuracy either by anyone at L-36.com or by the source which is typically the US Government. See the NOAA web site for their disclaimer. Finally, tide and current data on this site is from 2007 and 2008 data bases, which may contain even older data. Changes in harbors due to building or dredging change tides and currents and for that reason many of the locations presented are no longer supported by newer data bases. For example, there is very little tidal current data in newer data bases so current data is likely wrong to some extent. This data is NOT FOR NAVIGATION. See the XTide disclaimer for details. In addition, tide and current are influenced by storms, river flow, and other factors beyond the ability of any predictive program.