Cam100 User Guide 81272 1 En
This is a new page for displaying documents. The first time a document is loaded will take a little longer than it will for the next person so please be patient if it takes time. It will be much faster once all the documents have been converted. This will also allow these documents to display on devices without pdf viewers specifically mobile devices. Please email me at "L-36" dot COM if you notice any strange behavior. This is part of the Google requirement that all web pages be "mobile friendly". This is an effort that takes quite a bit of time and as it is just me and I would rather be sailing...
Note also that some documents have blank pages. Just click on "Next Page" if that happens.
PDF to Text.
Installation Technical Support
The adapter cable should be used to connect the display and the power supply to Technical specification
the camera. The adapter cable connections are shown below.
Format PAL 752 x 582 pixels
NTSC 768 x 494 pixels
Imager 1/3 Sony Super HAD CCD (Super Hi resolution)
Horizontal resolution 550 TVL
Scanning system PAL 625 lines
NTSC 525 lines 2:1 interlaced
Red +12 V
Black - 0 V Video output Composite 75 Ohms
Infra red 14 IR LEDs
If you do not have a breaker in the power circuit, an in-line 0.5 A quick blow fuse
should be fitted to the positive (red) lead of the cable. LED spectrum 30 degrees for 15m
Maintenance and Troubleshooting Minimum illumination 0.1 Lux at F2 - no IR, 0 Lux - with IR
Your Raymarine CAM 100 does not contain user-serviceable parts. Waterproof IPX6 and CFR46
They should be serviced only by authorized Raymarine service
technicians at a Raymarine factory facility. Power connection 12 V tinned leads
Routine Maintenance Video connections Male BNC
Routine maintenance should be carried out on a regular basis:
Operating temperatures -10oC to +55o C (-14o F to 130o F)
· Examine all cables for signs of damage such as chafing, cuts or nicks.
· Check that all cables are securely connected. Power consumption 130 mA - day, 280 mA - night, IR on @12 V DC
· Spray the camera and lens with fresh water and wipe with a soft lint-free
cloth to remove debris or salt deposits. Technical support
Complete product information and interactive help is available at:
Problem Solution North and South America Europe, Middle East, Africa
Camera does not function 1. Make sure that the cable is sound and Raymarine Technical Support
that all connections are tight and free 1-800-539-5539 Raymarine Technical Support
from corrosion. or, +1 603-881-5200 +44 (0) 23 9271 4713 D8531_1
2. Check system fuses.
3. Check that the display is set up Product Repair and Service Product Repair and Service
correctly to receive the images.
Refer to the relevant display Raymarine Product Repair Center Raymarine plc
handbook for full details. 21 Manchester Street, Anchorage Park
Merrimack, NH Portsmouth
03054-4801 PO3 5TD
EMC conformance USA England
All Raymarine equipment and accessories are designed to the best industry Help us to help you
standards for use in the recreational marine environment. The design and
manufacture of Raymarine equipment and accessories conforms to the
appropriate Electromagnetic Compatibility (EMC) standards, but correct
To allow us to respond to your needs faster, please quote the Equipment
type, Model number and Serial number when requesting service
installation is required to ensure that performance is not compromised.
Introduction What's in the box? Cable runs
The Raymarine CAM 100 CCTV camera is a high You need to consider the following points before installing the system cables:
quality 550 TVL horizontal resolution color · You need to connect the camera to the display unit and power supply.
camera available in two models: C · All cables should be adequately clamped and protected from physical damage
·E03006 - PAL format. A and exposure to heat - avoid running cables through bilges or doorways, or
·E03007 - NTSC format. close to moving or hot objects.
· Acute bends must be avoided.
The camera has 14 infra-red light emitting
diodes (LEDs) offering an extraordinary clear F
· Where a cable passes through an exposed bulkhead or deck head, a watertight
view in pitch black darkness.The unit is E gland or swan neck tube should be used.
waterproof to CFR46. · CCTV camera cables cannot be cut and rejoined.
Safety notices 1.Decide the camera position to obtain the best
D8533_1 coverage of the selected area.
CAUTION: Power supply
The Raymarine CAM 100 CCTV camera is suitable for 2.Drill holes for cable runs.
A. CCTV camera E. Pan head screws x 3
use on 12 V DC power supply only. 3.Thread the cable into position through the
B. Suncover F. Hex key mount .
CAUTION: Power supply
A 0.5A quick-blow fuse should be fitted to the positive C. Adjustable mounting bracket G. Adapter cable 4.Fix the adjustable mounting bracket into
(red) lead of the camera. D. Lens cover H. Nylon washers (not illustrated) position using nylon washers to protect
paintwork under the screw heads.
CAUTION: Camera lens
The camera lens cover is made of glass. Care should be What tools are required? D8535_1
5.Attach the camera to the mounting bracket
taken to avoid personal injury if broken. and lock in position using the locknut.
CAUTION: Installation The head of the bracket can be adjusted
This product IS NOT suitable for installation vertically through 90o and can be rotated
underwater. Drill Drill bit Phillips through 360o.
This product contains no user serviceable parts. D8534_1 6.Connect the camera to the display and fine
tune its orientation to obtain the best picture.
What accessories are available? 7.Lock the camera into the correct position using
To enable you to complete the cabling to install your camera the following accessories the allen key provided.
Waste Electrical and Electronic (WEEE) Directive
are available: D8536_1
The WEEE Directive requires the recycling of waste electrical and 8.Clip on the suncover.
· E06017 - 5m extension cable.
electronic equipment. Whilst the WEEE Directive does not apply to some · E06018 - 15 m extension cable.
of Raymarine's products, we support its requirements as part of our
You can join these cables in any combination to achieve the required cable length, but
environmental policy and we ask you to be aware of how you should
dispose of this product. The crossed out wheelie bin symbol found on
for optimum performance Raymarine recommend that the total cable length does not Cable connections
exceed 50 m.
our products signifies that it should not be disposed of in general waste or landfill. Male Female
The extension cables from the camera to the display unit are
Please contact your local dealer, national distributor or Raymarine Technical Services joined using the male/female twist connectors.
for information on product disposal.
Ad by Google
The information on this web site has not been checked for accuracy. It is for entertainment purposes only and should be independently verified before using for any other reason. There are five sources. 1) Documents and manuals from a variety of sources. These have not been checked for accuracy and in many cases have not even been read by anyone associated with L-36.com. I have no idea of they are useful or accurate, I leave that to the reader. 2) Articles others have written and submitted. If you have questions on these, please contact the author. 3) Articles that represent my personal opinions. These are intended to promote thought and for entertainment. These are not intended to be fact, they are my opinions. 4) Small programs that generate result presented on a web page. Like any computer program, these may and in some cases do have errors. Almost all of these also make simplifying assumptions so they are not totally accurate even if there are no errors. Please verify all results. 5) Weather information is from numerious of sources and is presented automatically. It is not checked for accuracy either by anyone at L-36.com or by the source which is typically the US Government. See the NOAA web site for their disclaimer. Finally, tide and current data on this site is from 2007 and 2008 data bases, which may contain even older data. Changes in harbors due to building or dredging change tides and currents and for that reason many of the locations presented are no longer supported by newer data bases. For example, there is very little tidal current data in newer data bases so current data is likely wrong to some extent. This data is NOT FOR NAVIGATION. See the XTide disclaimer for details. In addition, tide and current are influenced by storms, river flow, and other factors beyond the ability of any predictive program.