Saturday, September21, 2019 L-36.com

Traveler% Trimming



Note:

This is the new page for displaying documents. It allows documents to display on devices without pdf viewers specifically mobile devices, a new Google requirement. Note also that some documents have blank pages. Just click on "Next Page" if that happens.
Previous Page    Next Page Go to page number Note: Page number may not agree with index page numbers


Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.

  THE MAINSAIL TRIMMER AND THE TRAVELER   with Quantum222s David Flynn    The next best thing to driving a boat upwind is trimming the mainsail In fact to a large degree the mainsail trimmer is driving hunched over in the same pose eyes glued to the water ahead angle of heel telltales and speedo Constantly at hand are the primary tools of the trade the mainsheet and traveler   The traveler has two functions It controls the booms angle to the wind and it steers the boat controlling helm and heeling in puffs and lulls The basics are easy Set the twist with the mainsheet and then use the traveler to position the boom on the centerline for maximum power and pointing as long as helm and heeling are under control When helm and heeling become to great drop the traveler to maintain balance   Where the traveler car ends up is a function of mainsheet tension though in fact it is only the position of the boom relative to the centerline that counts The traveler car can be anywhere In light air when the mainsheet is well eased to promote acceleration the traveler car will need to be up to weather to put the boom on the centerline As the breeze builds and mainsheet tension increases the traveler will gradually be dropped to keep the boom on the centerline and eventually below centerline to depower the boat   Boats are a little different This is what makes it such a fun gamesheet and the traveler down Some like plenty of twist and leave the traveler up However regardless of design characteristics the mainsail trimmer operates in three basic modes Light under 10 knots1016 knots16  LIGHT AIR  Mainsail setup is characterized by plenty of twist mainsheet easedwith the traveler up The goal is promote helm and feel for the struggling driver without having to over sheet and stall the mainsail In light air add helm by pulling the traveler well up to weather The boom can even be slightly above centerline as long as the mainsheet is eased so there is plenty of twist In light conditions let the helm load up some before dropping the traveler to build speed Point with the traveler not additional sheet   MEDIUM AIR  In medium air as the boat becomes powered and the full crew begins to hikemain will be sheeted harder and the traveler will be dropped The mainsail can be sheeted quite hard and the traveler played aggressively to maintain the correct amount of helm Slick mainsail trimmers master the art of sheeting harder while lowering the traveler simultaneously In this range the traveler is the primary helm balance control As soon as there is too much heel and helm drop the traveler Having the boom on centerline is suddenly irrelevant As long as the puffs aren222t too big and sudden in which case it will be necessary to depower with by easing the mainsheettune balance with the traveler There is technique involved Dump the traveler down quickly at the onset of a puff but then be ready to pull it right back up as the initial power of the puff is dissipated and turned into forward speed instead of heel If you leave it down too long you will miss the opportunity to point once accelerated In medium air the range will be wide from the boom on centerline to all the way down  HEAVY AIR  In heavy air the traveler will be well down All boats reach a point where simply lowering the traveler is not enough to maintain balance At this point a modal shift is required It is time to go from using the traveler extensively to finetune helm to using the mainsheet to keep the boat on its feet Often the best trim solution is to fix the traveler six inches to a foot above the leeward coaming and play the sheet aggressively to control heel Keeping the traveler up a little keeps the bottom mainsail batten working which keeps the boat on the wind at the same time that power is being dumped from the top     SHEET VS TRAVELER  The eternal mainsailtrimming question must of course finally be asked with which do I depower the traveler or the mainsheet The answer of course both  As in all things to borrow from an ancient Zen saying 223the correct answer certainly lies in the middle way224 It is okay to use the big twist high traveler position in the light stuff but be ready to quickly change modes in the puffs at the transition between light and medium It is vital that the mainsail trimmer recognizes the boat222s sensitivity to this transition Likewise a second modal shift occurs when it becomes too windy for the traveler alone to maintain balance and the mainsheet must be brought back into the equation  Through it all always remember who is really driving the bus  

Ad by Google

Disclaimer:
The information on this web site has not been checked for accuracy. It is for entertainment purposes only and should be independently verified before using for any other reason. There are five sources. 1) Documents and manuals from a variety of sources. These have not been checked for accuracy and in many cases have not even been read by anyone associated with L-36.com. I have no idea of they are useful or accurate, I leave that to the reader. 2) Articles others have written and submitted. If you have questions on these, please contact the author. 3) Articles that represent my personal opinions. These are intended to promote thought and for entertainment. These are not intended to be fact, they are my opinions. 4) Small programs that generate result presented on a web page. Like any computer program, these may and in some cases do have errors. Almost all of these also make simplifying assumptions so they are not totally accurate even if there are no errors. Please verify all results. 5) Weather information is from numerious of sources and is presented automatically. It is not checked for accuracy either by anyone at L-36.com or by the source which is typically the US Government. See the NOAA web site for their disclaimer. Finally, tide and current data on this site is from 2007 and 2008 data bases, which may contain even older data. Changes in harbors due to building or dredging change tides and currents and for that reason many of the locations presented are no longer supported by newer data bases. For example, there is very little tidal current data in newer data bases so current data is likely wrong to some extent. This data is NOT FOR NAVIGATION. See the XTide disclaimer for details. In addition, tide and current are influenced by storms, river flow, and other factors beyond the ability of any predictive program.