L-36.com

End For End Splice For Class 2, Double Braid Ropes


Note: This is the new High Definition version of the Manual viewer with 4x the number of pixels per page.
Some manual pages may be blank. There will be an End of File notice after the last page.

Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.
end for end double braid Class Ii Class II double braid ropes are made in whole or part from any of the following Additional rope needed for splice high modulus fibers Dyneema Vectran Technora or Zylon 5 fid lengths 1 M a r k i n g t h e M e a s u r e mENTS Length of Z section based on size of rope as follows step From the end of each rope measure Size Dia 14 516 38 716 12 916 58 34 78 1 118 114 1516 112 and mark as follows Z Length 5 5 5 5 6 634 712 8 9 9 12 12 13 13 A 2 Fid Lengths from end Mark 1 on Cover and Core Mark 1 Cover and Core B From Mark 1 measure Z section 2 Fid Lengths lengths towards end of rope Mark cover only Z Mark Cover Only 2step KNOT a n d P o s i t i o n Measure back 6 Fid Lengths from Mark 1 and knot or spike each rope Position ropes as shown Z Make slipknot 6 fid lengths back from Mark 1 2 1 Make slipknot 6 fid lengths back from Mark 1 Z 3step Extract and mark cores Extract cores at Z Marks pull out completely from the ends of the ropes Tape core ends Slide covers back toward knotsspikes enhance Mark 1 on each core Measure 212 Fid lengths from core Mark 1 towards knotsspikes and make core Mark 2 on each core Extract Core Extracting the core Bend rope sharply at Z With the pusher or any sharp tool such as an ice pick awl or marlin spike spread the cover strands to expose core First pry then pull the core completely out of cover Z 212 Fid Lengths 2 1 212 Fid Lengths Z Page 1 of 2 2090 Thornton Street T 3603844669 Ferndale WA USA 98248 F 3603840572 end for end double braid Class Ii 4 Insert the end of each core into the opposing core at Mark 1 and out at Mark 2 Burying cores ep Inserting the core ends 1 pick down from Mark 1 on the entrance side of eachst core allows for a smoother crossover PUSH Mark 1 Z Mark 2 2 1 5 Z Ta p e r i n g c o r e ta i l s step From cut end mark strands as shown Cut and remove strands to form a tapered tail 6 Tighten crossover by milking towards the tighten crossover crossover from each directionstep Mark 1 Z Mark 2 Mark 2 1 2 Z Mark 1 7 step recovering core Z 1 Mark 1 Mark 1 2 Z 7A Milk away from the crossover in both directions Tapered tails will disappear Repeat until all slack is removed the crossover and entire splice length should be smooth Mark 1 Z Mark 2 Mark 2 1 2 Mark 1 Z 7B Milk the cover towards the crossover Work one side at a time hand tensioning the core splice area while working the cover up over it Mark 1 Z Covers should meet at or near the crossover Lock stitch 1 2 and whip each side of crossover and through cover tails see eye splice instructions Mark 1 Z 8step Lock stitch and WhiP Lock Stitch Whipping Page 2 of 2 2090 Thornton Street T 3603844669 Ferndale WA USA 98248 F 3603840572


NOTICE: Some pages have affiliate links to Amazon. As an Amazon Associate, I earn from qualifying purchases. Please read website Cookie, Privacy, and Disclamers by clicking HERE. To contact me click HERE. For my YouTube page click HERE