Thursday, August13, 2020
Privacy Policy

Firmware Upload


This is the new page for displaying documents. It allows documents to display on devices without pdf viewers specifically mobile devices, a new Google requirement. Note also that some documents have blank pages. Just click on "Next Page" if that happens.
Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.
1 Connect the appropriate cables to your PC and GSC 100 These cables were shipped with your unit Diagram below A Connect the RS232 software update cable to the datapower extension cable B Connect the RS232 software update cable to your PCs com port C Connect the datapower cable to your GSC 1002 Run the upload program A Turn your GSC 100 ON GSC 100 battery should be fully charged B Put your GSC 100 into GPS mode using the following procedure While in the MAIN MENU screen press the MNU key Highlight SYS MODE and press ENT Highlight GPS MODE and press ENT Your unit is now in GPS mode C If you are working in Windows 95 restart your computer in MSDOS mode this is an option under Shut Down If you are working in Windows 31 close all applications and any software programs and exit This will bring up the DOS prompt D In DOS go to the CTemp directory where the downloaded files from steps 1 and 4 are stored Both files must be in the same directory From the DOS prompt type cd ctemp and then Enter to move to the Temp directory E At the DOS prompt type the following using your PCs keyboard GSCUPLD GSCVxxxBIN then press the Enter key GSCVxxxBIN is the filename for the latest GSC 100 software downloaded in step 1 xxx refers to the version number such as GSCV108bin Your PC will download your GSC 100s waypoints routes messages and addresses onto the PC disk erase your units memory and then upload the latest software into your GSC 100 This user specific information will be reloaded into your GSC 100 after the new software is uploaded You will see the following on your PC screen WAITING FOR UNIT RESPONSE ERASING EPROMs Your PC will count up to 100 which takes approximately 23 minutes Once upload is complete your GSC 100 will automatically turn OFF You will then see the following on your PC screen 1000 complete CODE DONE FINISH ACKNOWLEDGED Turn on the unit by pressing the power key Then press a key on the PC to upload data F Turn your GSC 100 ON by pressing the PWR key and then press the key with the letter A on your PC keyboard to upload data Your PC will display WAITING FOR UNIT RESPONSE RESTORING DATA TO GSC100 UNIT SOFTWARE Upload completed Wait until your PC screen displays Upload completed3 Turn your PC and GSC 100 OFF then disconnect all the cables from your PC and your GSC 1004 Turn on and reinitialize your GSC 100 Take it outside and allow it to calculate a position fix Once ithas a GPS fix it will calculate correct ORBCOMM satellite pass times5 You are now ready to use your GSC 100 with the updated software

Ad by Google

Cookie Policy:
This website uses cookies to save your settings. No personal information is saved. I do not collect statistics on your visit. You can disable cookies in your browser if you like but it is not recommended for this site. I do not sell cookies. Go to a bakery for that. In fact I do not sell anything. To disable cookies from, please refer to the Help button in your browser.
Privacy Policy:
I do not sell or share any user data or anything else for that matter. The only personal information I save is in the site log which has a line for each page view which includes the IP address your browser sends in the header as well as which page you requested. I use this to block hackers and other bad actors. I do not use this raw data to create profiles on users. I periodically delete the log files. If you are subject to CCPA, Google ads on this site will not be based on your past behavior so you will likely not see an ad for a lawn mower just because you looked for one at a big box website. I do not believe this site is subject to CCPA but I am doing what I can to follow the guidelines anyway.
The information on this web site has not been checked for accuracy. It is for entertainment purposes only and should be independently verified before using for any other reason. There are five sources. 1) Documents and manuals from a variety of sources. These have not been checked for accuracy and in many cases have not even been read by anyone associated with I have no idea of they are useful or accurate, I leave that to the reader. 2) Articles others have written and submitted. If you have questions on these, please contact the author. 3) Articles that represent my personal opinions. These are intended to promote thought and for entertainment. These are not intended to be fact, they are my opinions. 4) Small programs that generate result presented on a web page. Like any computer program, these may and in some cases do have errors. Almost all of these also make simplifying assumptions so they are not totally accurate even if there are no errors. Please verify all results. 5) Weather information is from numerous of sources and is presented automatically. It is not checked for accuracy either by anyone at or by the source which is typically the US Government. See the NOAA web site for their disclaimer. Finally, tide and current data on this site is from 2007 and 2008 data bases, which may contain even older data. Changes in harbors due to building or dredging change tides and currents and for that reason many of the locations presented are no longer supported by newer data bases. For example, there is very little tidal current data in newer data bases so current data is likely wrong to some extent. This data is NOT FOR NAVIGATION. See the XTide disclaimer for details. In addition, tide and current are influenced by storms, river flow, and other factors beyond the ability of any predictive program.