L-36.com

Raymarine E Series Widescr Installation Instructions 87116 3


Note: This is the new High Definition version of the Manual viewer with 4x the number of pixels per page.
Some manual pages may be blank. There will be an End of File notice after the last page.

Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.
ESeries E120W and E140W and patents noticeAutohelm hsb2 RayTech Navigator Sail Pilot SeaTalk SeaTalkNG SeaTalkHS and Sportpilot are registered trademarks of RaymarineUK Limited RayTalk Seahawk Smartpilot Pathfinder and Raymarine are registered trademarks of Raymarine Holdings LimitedFLIR is a registered trademark of FLIR Systems Inc andor its other trademarks trade names or company names referenced herein are used for identification only and are the property oftheir respective ownersThis product is protected by patents design patents patents pending or design patents pendingFair Use StatementYou may print no more than three copies of this manual for your own use You may not make any further copies or distribute or use themanual in any other way including without limitation exploiting the manual commercially or giving or selling copies to third 2010 Raymarine UK Ltd All rights number 871163Date 1 Important information 7 Chapter 3 Cables and connections 23TFT LCD Displays 8 31 General cabling guidance 24Water ingress 8 32 Connections overview 25Disclaimers 9 33 Power connection 25Chart cards and memory cards9 34 SeaTalkhs network 28EMC installation guidelines 9 35 NMEA 0183 connection 37Suppression ferrites 10 36 SeaTalk connection 38Connections to other equipment 10 37 Alarm connection 39Declaration of conformity 10 38 GPS connection 40Product disposal 10 39 AIS connection 41Warranty registration 10 310 FastHeading connection 42IMO and SOLAS 11 311 SeaTalkng connections 43Technical accuracy 11 312 NMEA 2000 connection 44 313 Video and alarm audio connection 45Chapter 2 Planning the installation 1321 Handbook information 14 Chapter 4 Location and mounting 4922 Installation checklist 14 41 Selecting a location 5023 ESeries Widescreen system 15 42 Flush mounting 5224 System protocols 17 43 Bracket trunnion mounting 5325 Networking constraints 18 44 Front bezel 5526 Data master 20 Chapter 5 System checks 5727 Pack contents 20 51 Initial power on test 5828 Tools 21 52 Designating the data master 59 553 GPS check 59 81 Technical specification 9254 Radar check 60 Chapter 9 Options and accessories 9555 Sonar check 62 91 SeaTalk accessories 9656 Thermal camera setup and checks 63 92 SeaTalkng accessories 9657 Language selection 64 93 SeaTalkhs accessories 9758 Setting up Autopilot AIS and Navtex 65 94 Spares and accessories 9959 System setup menu 66 Appendix A Multifunction display systemChapter 6 73 integration 10361 7462 Power up 75 Appendix B NMEA 0183 sentences 10663 Radar 7664 GPS 77 Appendix C NMEA 2000 sentences 10865 Sonar 7866 Thermal camera 79 Appendix D Connectors and pinouts 11167 System data 8268 Video 8369 Touchscreen 84610 SeaTalkhs LED indications 85611 Miscellaneous 86Chapter 7 Technical support 8771 Raymarine customer support 8872 3rd party support 89Chapter 8 Technical specification 916 ESeries Widescreen 1 Important information Warning Switch off power supply Warning Product installation and Ensure the boats power supply is switched OFF before starting to install this product Do NOT connect operation or disconnect equipment with the power switched on This product must be installed and operated in unless instructed in this document accordance with the instructions provided Failure to do so could result in personal injury damage to your Warning Radar scanner safety boat andor poor product performance Before rotating the radar scanner ensure all personnel are clear Warning Potential ignition source This product is NOT approved for use in Warning Radar transmission safety atmospheres Do NOT install in a atmosphere such as in an The radar scanner transmits energy engine room or near fuel tanks Ensure all personnel are clear of the scanner when the radar is transmitting Warning High voltages This product contains high voltages Do NOT remove Warning Sonar operation any covers or otherwise attempt to access internal NEVER operate the sounder with the boat out of components unless specifically instructed in this the water document NEVER touch the transducer face when the sounder is powered on Warning Product grounding SWITCH OFF the sounder if divers are likely to be Before applying power to this product ensure it has within 76 m 25 ft of the transducer been correctly grounded in accordance with the instructions in this guide Warning Touchscreen display When exposed to prolonged periods of direct sunlight the touchscreen display can get very hot In such conditions avoid using the touchscreen display and use the units physical keys and buttons information 7 Caution Power supply protection Caution Cleaning When installing this product ensure the power source When cleaning this product is adequately protected by means of a suitablyrated fuse or automatic circuit breaker Do NOT wipe the display screen with a dry cloth as this could scratch the screen coating Do NOT use abrasive or acid or ammonia based Caution Care of chart cards products To avoid irreparable damage to andor loss of data Do NOT use a jet wash from chart cards Ensure that chart cards are fitted the correct way around DO NOT try to force a card into position DO NOT save data waypoints routes and so on TFT LCD Displays to a chart card as the charts may be overwritten The colors of the display may seem to vary when viewed against DO NOT use a metallic instrument such as a a colored background or in colored light This is a perfectly normal screwdriver or pliers to remove a chart card effect that can be seen with all color Liquid Crystal Displays LCDs Safe removal Use the Remove Card menu option In common with all Thin Film Transistor TFT LCD units the screen before removing the chart card may exhibit a few less than 7 wrongly illuminated pixels These may appear as black pixels in a light area of the screen or as colored pixels in black areas Caution Ensure chart card door is securely closed To prevent water ingress and consequent damage to Water ingress the display ensure that the chart card door is firmly closed This can be confirmed by an audible click Water ingress disclaimer Although the waterproof rating capacity of Raymarine products Caution Use the sun covers exceeds that called for by the IPX6 standard water intrusion and subsequent equipment failure may occur if any Raymarine To protect your product against the damaging effects equipment is subjected to commercial high pressure washing of ultra violet light always fit the sun covers when the Raymarine will not warrant equipment subjected to high pressure product is not in use washing8 ESeries Widescreen micro Secure Digital HighCapacity microSDHCThis product including the electronic charts is intended to be used Note microSD and microSDHC cards require the optionalonly as an aid to navigation It is designed to facilitate use of official Raymarine CF microSD card adaptor Only the charts not replace them Only official government Raymarine adaptor is compatible with your systemcharts and notices to mariners contain all the current for safe navigation and the captain is responsible for theirprudent use It is the users responsibility to use official government Chart cardscharts notices to mariners caution and proper navigational skill Your system is preloaded with electronic charts for your region Ifwhen operating this or any other Raymarine product This product you wish to use different chart data you can insert compatible CFsupports electronic charts provided by third party data suppliers chart cards into the CompactFlash card slot on your unit If youwhich may be embedded or stored on memory card Use of such want to use microSD or microSDHC chart cards you must purchasecharts is subject to the suppliers EndUser Licence Agreement the optional CF microSD card adaptor and insert it into theincluded in the documentation for this product or supplied with the CompactFlash card slot on your unit The microSD or card as applicable chart card must be inserted into the does not warrant that this product is errorfree or that itis compatible with products manufactured by any person or entity Use branded chart cards and memory cardsother than Raymarine When archiving data Raymarine recommends the use of qualityThis product uses digital chart data and electronic information from branded memory cards Some brands of memory card may notthe Global Positioning System GPS which may contain errors work in your unit Please contact customer support for a list ofRaymarine does not warrant the accuracy of such information and recommended cardsyou are advised that errors in such information may cause theproduct to malfunction Raymarine is not responsible for damagesor injuries caused by your use or inability to use the product by theinteraction of the product with products manufactured by others or EMC installation guidelinesby errors in chart data or information utilized by the product andsupplied by third parties Raymarine equipment and accessories conform to the appropriate Compatibility EMC regulations to minimize interference between equipment and minimize the effect such interference could have on the performance of yourChart cards and memory cards cards Correct installation is required to ensure that EMC performance is not compromisedThe following types of memory or chart card are compatible withyour Raymarine system For optimum EMC performance we recommend that wherever possible CompactFlash CF micro Secure Digital microSD Raymarine equipment and cables connected to it areImportant information 9 At least 1 m 3 ft from any equipment transmitting or cables Connections to other equipment carrying radio signals eg VHF radios cables and antennas In the case of SSB radios the distance should be increased Requirement for ferrites on nonRaymarine cables to 7 ft 2 m If your Raymarine equipment is to be connected to other equipment More than 2 m 7 ft from the path of a radar beam A radar using a cable not supplied by Raymarine a suppression ferrite beam can normally be assumed to spread 20 degrees above MUST always be attached to the cable near the Raymarine unit and below the radiating element The product is supplied from a separate battery from that used for engine start This is important to prevent erratic behavior Declaration of conformity and data loss which can occur if the engine start does not have a separate battery Raymarine Ltd declares that GSeries systems are in compliance with the essential requirements of EMC directive 2004108EC Raymarine specified cables are used The original Declaration of Conformity certificate may be viewed on Cables are not cut or extended unless doing so is detailed in the relevant product page at the installation manual Note Where constraints on the installation prevent any of the above always ensure the maximum Product disposal possible separation between different items of electrical equipment to provide the best conditions for EMC performance Dispose of this product in accordance with the WEEE Directive throughout the installation The Waste Electrical and Electronic Equipment ferrites Directive requires the recycling of waste electrical and electronic equipment Whilst the WEEE Directive does not apply to some Raymarine products we support its policy and ask you to be awareRaymarine cables may be fitted with suppression ferrites These of how to dispose of this productare important for correct EMC performance If a ferrite has to beremoved for any purpose eg installation or maintenance it mustbe replaced in the original position before the product is usedUse only ferrites of the correct type supplied by Raymarine Warranty dealers To register your ESeries Widescreen multifunction display ownership please take a few minutes to fill out the warranty registration card found in the box or visit and register online10 ESeries Widescreen installationIt is important that you register your product to receive full Your unit package includes a bar code label indicating theserial number of the unit You should stick this label to the cardIMO and SOLASThe equipment described within this document is intended for useon leisure marine boats and workboats not covered by Organization IMO and Safety of Life at Sea SOLASCarriage accuracyTo the best of our knowledge the information in this document wascorrect at the time it was produced However Raymarine cannotaccept liability for any inaccuracies or omissions it may contain Inaddition our policy of continuous product improvement may without notice As a result Raymarine cannot for any differences between the product and this information 1112 ESeries Widescreen 2 Planning the contents 21 Handbook information on page 14 22 Installation checklist on page 14 23 ESeries Widescreen system on page 15 24 System protocols on page 17 25 Networking constraints on page 18 26 Data master on page 20 27 Pack contents on page 20 28 Tools on page 21Planning the installation 1321 Handbook information 22 Installation checklistThis handbook contains important information regarding the Installation includes the following Widescreen range of multifunction displays Installation TaskThe handbook is for use with the following models 1 Plan your system E90W Widescreen Multifunction Display 2 Obtain all required equipment and tools E120W Widescreen Multifunction Display 3 Site all equipment E140W Widescreen Multifunction Display 4 Route all cablesESeries handbooks 5 Drill cable and mounting holesThe ESeries Widescreen Multifunction Display has the following 6 Make all connections into available 7 Secure all equipment in placeAll documents are available to download as PDFs 8 Power on test the systemESeries handbooks Description Part number Installation and commissioning 87116 instructions Operating instructions quick 86137 reference User reference handbook handbooks Description Part number SeaTalkng reference manual 8130014 ESeries Widescreen installation23 ESeries Widescreen systemThe ESeries Widescreen display can be connected to a variety of equipment as part of your marine electronics systemBasic system example RS125 GPS ESeries Widescreen display SeaTalkhs switch Digital sounder Digital Radome DSM SeaTalkhs SeaTalk SeaTalkhs SeaTalkhs Autopilot Controller Autopilot ST6002 NMEA0183 the installation 15Expanded system example Digital Devices Autopilot Instrument AIS 500 Sirius Weather Digital Sounder Digital Radar Antenna SR100 DSM AIS 500 CANCEL ENTER CANCEL ENTER MENU MENU SeaTalkng SeaTalkng SeaTalkng GSeries Monitor SeaTalkng backbone RS125 GPS Engine Devicenet Spur ESeries Widescreen display Video SeaTalkhs switch ESeries Widescreen display data master SeaTalkhs Alarm SeaTalkhs D116831 Note The system allows up to 5 ESeries Widescreen displays to be connected on a SeaTalkhs network16 ESeries Widescreen installation24 System protocols Seatalkng SeaTalkng Next Generation is an enhanced protocol for connectionYour Multifunction Display can connect to various instruments and of compatible marine instruments and equipment It replaces thedisplays to share information and so improve the functionality of older SeaTalk and SeaTalk2 protocolsthe system These connections may be made using a number ofdifferent protocols Fast and accurate data collection and transfer is SeaTalkng utilizes a single backbone to which by using a combination of the following data protocols instruments connect using a spur Data and power are carried within the backbone Devices that have a low draw can be powered from SeaTalkhs the network although high current equipment will need to have a SeaTalkng separate power connection NMEA 2000 SeaTalkng is a proprietary extension to NMEA 2000 and the proven CAN bus technology Compatible NMEA 2000 and SeaTalk SeaTalk SeaTalk2 devices can also be connected using the appropriate interfaces or adaptor cables as required NMEA 0183 NMEA 2000 Note You may find that your system does not use all of the connection types or described in this section NMEA 2000 offers significant improvements over NMEA 0183 most notably in speed and connectivity Up to 50 units can simultaneously transmit and receive on a single physical bus at any one timeSeaTalkhs with each node being physically addressable The standard was specifically intended to allow for a whole network of is an ethernet based marine network This high speed electronics from any manufacturer to communicate on a commonprotocol allows compatible equipment to communicate rapidly and bus via standardized message types and formatsshare large amounts of shared using the SeaTalkhs network includes SeaTalk Shared cartography between compatible displays SeaTalk is a protocol which enables compatible instruments to Digital radar data connect to each other and share data Sonar data The SeaTalk cable system is used to connect compatible instruments and equipment The cable carries power and data and enables connection without the need for a central processor Additional instruments and functions can be added to a SeaTalk system simply by plugging them into the network SeaTalk equipment can also communicate with other nonSeaTalk equipment via the NMEA 0183 standard provided a suitable interface is usedPlanning the installation 17NMEA 0183 25 Networking constraintsThe NMEA 0183 Data Interface Standard was developed by The following constraints apply when networking an ESeriesthe National Marine Electronics Association of America It is an Widescreen display with a GSeries standard to enable equipment from many to be connected together and share information GeneralThe NMEA 0183 standard carries similar information to SeaTalk ESeries Widescreen displays must be connected to the GSeriesHowever it has the important difference that one cable will only system via SeaTalkhscarry information in one direction For this reason NMEA 0183 isgenerally used to connect a data receiver and a transmitter together ESeries Widescreen displays can be connected via NMEA 0183eg a compass sensor transmitting heading to a radar display This ESeries Widescreen displays must NOT be connected toinformation is passed in sentences each of which has a three SeaTalkng when part of a GSeries networkletter sentence identifier It is therefore important when between items that the same sentence identifiers are ESeries Widescreen displays must NOT be connected to SeaTalkused some examples of which are when part of a GSeries network VTG carries Course and Speed Over Ground data Master slave operation GLL carries latitude and longitude When using an ESeries Widescreen display in a GSeries system the GSeries GPM processor unit is ALWAYS the data DBT carries water depth master MWV carries relative wind angle and wind speed data Nav stationsNMEA baud rates An ESeries Widescreen display can NOT form part of a GSeries Nav Station NMEA 0183 standard operates at a number of depending upon the particular requirement or equipment Home screen Typical examples are For networks featuring ONLY ESeries Widescreen units 4800 baud rate Used for general purpose communications including FastHeading data Networked ESeries Widescreen units share home screens 9600 baud rate Used for Navtex For networks featuring ONLY GSeries GPM processor units 38400 baud rate Used for AIS and other high speed applications Networked GPM processor units share home screens For networks featuring ESeries Widescreen AND GSeries GPM processor units ESeries Widescreen units share home screens GPM processor units share home screens18 ESeries Widescreen installation ESeries Widescreen units do NOT share home screens with Keyboards GPM processor units If a SeaTalkng keyboard is being used to control an sharing Widescreen display it must be connected directly to the ESeries Widescreen display using SeaTalkng It must NOT be connected Chart card cartography is shared between ESeries Widescreen to the GSeries SeaTalkng bus displays and GSeries GPM processor units GPS Embedded cartography can NOT be shared between ESeries Widescreen displays and GSeries GPM processor units A networked system does NOT support multiple GPS receivers An ESeries Widescreen display will share its embedded cartography with another ESeries Widescreen display on the same network A GSeries GPM processor unit will share its embedded cartography with other GSeries GPM processor units on the same network The cartography contained on chart cards is always used in preference to embedded cartography when a chart card is inserted into a card slotRadar operation The GSeries system supports the use of 2 radar scanners at the same time An ESeries Widescreen display in a GSeries system can operate 1 scanner at any one time To use the second scanner you must select it in the Radar applications Setup Menu This does not automatically power down the first scanner When 2 scanners are connected you can powerdown the second scanner at any time using the radar power controls accessible from the displays power button The rotating scanner icon in the status bar indicates the status of all connected scanners not just the currently selected scanner Similarly if you have a GSeries Compact keyboard connected to an ESeries Widescreen display the radar status LED located on the keyboard reflects the status of ALL the installation 1926 Data master 27 Pack contentsAny system containing more than one networked multifunction All models contain the following itemsdisplay must have a designated data masterThe data master is the display which serves as a primary sourceof data for all displays it also handles all external sources ofinformation For example the displays may require from the autopilot and GPS systems usually a SeaTalkng or NMEA connection The data master is thedisplay to which the SeaTalk NMEA and any other data connectionsare made it then bridges the data to the SeaTalkhs network andany compatible repeat displays Information shared by the datamaster includes Cartography Routes and waypoints Radar 1 Sonar Data received from the autopilot instruments the engine and 4 2 other external sourcesYour system may be wired for redundancy with data connections 3made to repeat displays However these connections will only 5become active in the event of a fault andor reassignment of thedata master 6 7 D11684220 ESeries Widescreen installation Number Description 28 Tools 1 Gasket Tools required for installation 2 ESeries Widescreen Multifunction Display 3 Bezel 4 Suncover 5 15 m 49 ft Power and data cable 6 Screw pack 7 Document pack includes Multilingual CD Power Jig drill saw Installation and commissioning instructions Quick reference User reference Cutting template drill bit End User License Agreement EULA Adhesive tape bracket mounting the display unit carefully to prevent damage Save thecarton and packing in case the unit has to be returned for service File 35 mm 138 in 5 mm 316 in drill bit hole cutter bracket mounting panel mounting the installation 2122 ESeries Widescreen 3 Cables and contents 31 General cabling guidance on page 24 32 Connections overview on page 25 33 Power connection on page 25 34 SeaTalkhs network on page 28 35 NMEA 0183 connection on page 37 36 SeaTalk connection on page 38 37 Alarm connection on page 39 38 GPS connection on page 40 39 AIS connection on page 41 310 FastHeading connection on page 42 311 SeaTalkng connections on page 43 312 NMEA 2000 connection on page 44 313 Video and alarm audio connection on page 45Cables and connections 2331 General cabling guidance Always route data cables as far away as possible from other equipment and cablesCable types and length high current carrying ac and dc power linesIt is important to use cables of the appropriate type and length antennae Unless otherwise stated use only standard cables of the correct type supplied by Raymarine Strain relief Ensure that any nonRaymarine cables are of the correct quality and gauge For example longer power cable runs may require Ensure adequate strain relief is provided Protect connectors from larger wire gauges to minimize voltage drop along the run strain and ensure they will not pull out under extreme sea cables Circuit must be routed correctly to maximize performance and Appropriate circuit isolation is required for installations using bothprolong cable life AC and DC current Do NOT bend cables excessively Wherever possible ensure a Always use isolating transformers or a separate powerinverter minimum bend radius of 100 mm to run PCs processors displays and other sensitive electronic instruments or devices Always use an isolating transformer with Weather FAX audio Minimum bend 200 mm 8 in cables diameter Always use an isolated power supply when using a 3rd party Minimum bend of cable 100 mm 4 in radius audio amplifier Always use an RS232NMEA converter with optical isolation on the signal lines Protect all cables from physical damage and exposure to heat Always make sure that PCs or other sensitive electronic devices Use trunking or conduit where possible Do NOT run cables have a dedicated power circuit through bilges or doorways or close to moving or hot objects Secure cables in place using tiewraps or lacing twine Coil any Cable shielding extra cable and tie it out of the way Ensure that all data cables are properly shielded that the cable Where a cable passes through an exposed bulkhead or deckhead shielding is intact eg hasnt been scraped off by being squeezed use a suitable watertight feedthrough through a tight area Do NOT run cables near to engines or fluorescent lights24 ESeries Widescreen installation32 Connections overview 33 Power connectors are on the rear of the display Widescreen display 19 way multicable 7Afuse Red 1 2 3 4 D116881 12 V 24 V Data and video Black supply1 SeaTalkng D1121022 Power data and 1 x video in Power distribution3 SeaTalkhs Raymarine recommend that all power connections are made via a4 Additional 3 x Video in 1 x video out and alarm audio line out distribution panel All equipment must be powered from a breaker or switch with appropriate circuit protection All equipment should where possible be wired to individual breakersCables and connections 25 Warning Product grounding The preferred minimum requirement for the path to ground bonded or nonbonded is via a flat tinned copper braid with a 30 A rating Before applying power to this product ensure it has 14 inch or greater If this is not possible an equivalent stranded been correctly grounded in accordance with the wire conductor may be used rated as follows instructions in this guide for runs of 1 m 3 ft use 6 mm2 10 AWG 6 mm or greater for runs of 1 m 3 ft use 8 mm2 8 AWG or In any grounding system always keep the length of connectingThe following requirements apply when grounding Raymarine braid or wires as short as which does not have a dedicated drain wire or shield Important Do NOT connect this product to a ground point power systemThe negative wire must be connected to a bonded common groundpoint i e with the ground point connected to battery negative and as close as possible to the battery negative terminal ISO 1013313297 BMEA code of practice NMEA 0400 Power cable The display is supplied with a combined power and data multi cable this can be extended if required Power cable supplied 1 2 3 D117051 Cable Part number Notes1 Power cable to display 15 m 49 ft Power and R62131 Supplied with unit2 Bonded common ground connection data cable3 Battery Cable The following restrictions apply to any extension to the power cableIf several items require grounding they may be first be connected Cable must be of a suitable gauge for the circuit loadto a single local point eg within a switch panel with this pointconnected via a single conductor to the boats Each unit should have its own dedicated power cable wired backcommon ground to the distribution panel26 ESeries Widescreen installation Total length max Supply voltage Cable gauge AWG Sharing a breaker 05 m 0164 ft 12 V 18 Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits Eg by connecting an 24 V 20 inline fuse for each power circuit 510 m 164328 ft 12 V 14 VE bar VE bar 24 V 18 1015 m 328492 ft 12 V 12 Where possible connect individual items of equipment to individual circuit breakers 24 V 16 Where this not possible use individual inline 1520 m 492655 ft 12 V 12 fuses to provide the necessary protection 24 V 14 Circuit breaker Note These distances are for a 2 wire power cable run from the battery to the display approximately the distance from the battery to the display To calculate the round trip length double the figure stated hereBreakers fuses and circuit protectionThe power cable includes an inline fuse It is recommended thatyou fit an additional thermal breaker or fuse at the distribution panel Fuse Fuse D116371 Display Fuse C90W E90W 7 A inline fuse fitted within power cable C120W E120W C140W E140WCables and connections 2734 SeaTalkhs networkThe SeaTalkhs network allows you to connect compatible displays and other digital can be used with ESeries Widescreen to Create a network of up to 5 ESeries Widescreen displays Connect a digital radar scanner Connect a digital sounder DSM Note A network containing more than a single connection will require a SeaTalkhs switch This is a hub used for connection of multiple devicesTypical SeaTalkhs network 1 2 4 SeaTalkhs SeaTalkhs 5 3 SeaTalkhs SeaTalkhs D11689128 ESeries Widescreen installation1 Data master display2 Repeat display3 SeaTalkhs switch4 Digital radar scanner5 Digital sounder eg DSM400Radar connectionThe display is compatible with Raymarine digital radar scannersThe scanner is connected using a SeaTalkhs cableThe digital radar is usually connected via a SeaTalkhs switch Onsmaller systems with only one display and no other digital devicesthe radar may be connected using a crossover couplerCables and connections 29Radar connected using SeaTalkhs switch 3 SeaTalkhs switch 4 VCM100 power converter This is only required with open array type scanners 5 Connection to power supply Radar connected directly to the display 1 Note The connector on the free end of the radar cable does not 2 have a locking weather tight mechanism The use of a crossover coupler is important to create a weather proof connection 3 4 5 D1168611 Display2 Digital radar scanner30 ESeries Widescreen installation 1 2 3 4 D1168511 Digital radar scanner2 Display3 Crossover coupler4 Connection to power supplyCables and connections 31Digital radar cable extensionIf required you can use a Raymarine digital radar extension cable 1 2 D116873 D1168711 Extension cable2 Digital scanner cable Note The extension cable connects to the radar scannerDigital radar cables Radar scanner to SeaTalkhs switch or crossover couplerFor longer cable runs a range of extensions is available forSeaTalkhs and radar scanner power and data digital cables Digital scanner cables Connect the Radar scanner to the SeaTalkhs switch or crossover Note The maximum length for the radar power and data digital coupler and power supply These cables contain both power and cable including all extensions is 25 m 82 ft data wires32 ESeries Widescreen installation Cable Part number Notes Cable Part number Notes 5 m 164 ft Digital cable A55076 15 m 49 ft SeaTalkhs E55049 network cable 10 m 328 ft Digital A55077 cable 5 m 164 ft SeaTalkhs E55050 network cable 15 m 492 ft Digital A55078 cable 10 m 328 ft SeaTalkhs E55051 network cable 25 m 820 ft Digital A55079 cable 20 m 656 ft SeaTalkhs E55052 network cableExtension cables SeaTalkhs hardwareUse of one of these cables to extend the radar connection to theSeaTalkhs switch or crossover coupler and power supply These To connect the digital radar to a multifunction display you will needcables contain both power and data wires to include one of the following Cable Part number Notes Cable Part number Notes 25 m 82 ft extension A92141 SeaTalkhs switch E55058 8way hub for network cable connection of multiple SeaTalkhs devices 5 m 164 ft extension A55080 cable SeaTalkhs coupler E55060 Coupler for connection of a single SeaTalkhs 10 m 328 ft extension A55081 device cableSeaTalkhs switch or crossover coupler to display unitSeaTalkhs network cablesConnect from the SeaTalkhs switch or the crossover coupler into therear of the displayCables and connections 33Sonar connection The ESeries Widescreen display can be used with the following DSM unitsThe sonar connection is required for fishfinder applications Thedisplay is connected to a sonar module DSM using a SeaTalkhs DSM400cable You will also require a compatible transducer connected tothe DSM unit DSM300 DSM30 The display can support 1 DSM module 1 Sonar connected directly to the display On smaller systems with only one display and no other digital devices the DSM may be connected directly to the display without using a SeaTalkhs switch Note You must ensure that the cable ends connected into the display and DSM have a locking weather tight mechanism Typical DSM system 2 1 2 SeaTalk hs 3 3 SeaTalk hs D1168011 Display2 SeaTalkhs switch 4 SeaTalkhs3 DSM unit eg DSM400 D11681134 ESeries Widescreen installation1 DSM unit eg DSM400 Thermal camera connection2 Display You can connect a thermal camera to your multifunction display The camera is connected via a SeaTalkhs switch If you want to3 SeaTalkhs switch use the optional Joystick Control Unit JCU with the camera this4 Transducer must also be connected to the SeaTalkhs switch A composite video connection is required between the camera and the cable displayConnect the DSM unit directly to your display or connect via the 1 2SeaTalkhs network cablesConnect from the SeaTalkhs switch into the rear of the display Cable Part number Notes 15 m 49 ftSeaTalkhs E55049 network cable 5 m 164 ft SeaTalkhs E55050 network cable SeaTalkhs 7 SeaT 10 m 328 ft SeaTalkhs E55051 alkhs network cable 4 3 20 m 656 ft SeaTalkhs E55052 network cable 6Fully waterproof SeaTalkhs network cables 5Connect directly from DSM to the rear of the display SeaTalkhs Cable Part number Notes D119321 15 m 49 ft SeaTalkhs A62245 Cable has waterproof network cable connectors at both ends 1 Multifunction display 2 SeaTalkhs switch 10 m 328 ft SeaTalkhs A62246 Cable has waterproof network cable connectors at both ends 3 PoE Power over Ethernet injector only required if using the optional JCUCables and connections 354 Joystick Control Unit JCU optional Thermal camera cables5 Cable coupler Cabling requirements for thermal cameras6 Thermal camera Camera to SeaTalkhs switch7 Video connection You will need a SeaTalkhs patch cable to connect the camera to the SeaTalkhs switch The connection is made between the notes cable tail to the switch via the coupler supplied with the camera Patch cables are available in a variety of lengths You can control the thermal camera using your display The Joystick Control Unit JCU is optional but can be Joystick Control Unit JCU used in conjunction with the display to control the thermal camera if required An Ethernet with power cable is used to connect the JCU The JCU is supplied with a 15 m 5 ft Ethernet cable for this connection if Dual payload thermal cameras include 2 independent lenses 1 you require a different length contact your dealer for suitable cables for thermal infrared and visible light 1 for thermal infrared only If you only have 1 display you should only connect the video cable Power over Ethernet PoE injector to SeaTalkhs switch labelled VIS IR visible light infrared to the display If you have 2 or more displays you should connect 1 cable to each display A SeaTalkhs patch cable is required for connecting the PoE injector to the SeaTalkhs switch SeaTalkhs patch cables are available in a The thermal camera must be connected to Video Input 1 on the variety of lengths multifunction display Video cables You can only view the thermal camera image on the multifunction display to which the camera is physically connected If you want Contact your dealer for suitable cables and adaptors to view the thermal camera image on more than 1 display you must obtain a suitable thirdparty video distribution unit SeaTalkhs patch cables Thermal camera support requires the latest ESeries Widescreen Cable Part number software To check your software version select MENU System 15 m 49 ft SeaTalkhs patch cable E06054 Diagnostics Software Services Unit Info App Version Refer to the Raymarine website for latest 5 m 164 ft SeaTalkhs patch cable E06055 software versions 10 m 328 ft SeaTalkhs patch cable E06056 For further information regarding the cameras installation including connections and mounting refer to the installation 15 m 492 ft SeaTalkhs patch cable A62136 instructions that accompany the camera 20 m 656 ft SeaTalkhs patch cable E0605736 ESeries Widescreen installation35 NMEA 0183 connection Port 1 Input and output 4800 9600 baud to NMEA 0183 devices are made using the supplied Port 2 Input and output up to 38400 baud ratePower and data cable Port 3 Input only 4800 baud rate NMEA 0183 cable You can extend the NMEA 0183 wires within the supplied power and data cable Data cable extension Widescreen display The following restrictions apply to any extension to the NMEA 0183 data wires Total length max Cable Up to 5 m High quality data cable 2 x twisted pair with overall shield White Green Yellow Brown Orange Orange Blue 50 to 75 pFm capacitance core to IN IN OUT OUT Green Brown Green core ve ve ve ve IN OUT IN ve ve ve Orange Orange Blue White Y ellow White IN OUT IN ve ve ve OUT OUT IN IN OUT OUT IN IN OUT OUT ve ve ve ve ve ve ve ve ve ve NM EA NM EA NMEA DEVICE DEVICE DEVICE 48009600 baud 4800960038400 baud 4800 baud transmit to display only D112002The display has 3 NMEA ports and connections 3736 SeaTalk connection SeaTalk cable For SeaTalk cables and extensions use Raymarine SeaTalk to SeaTalk equipment are made using the supplied Note Power to SeaTalk instruments is not provided by the display Widescreen display 19 way multicable Power data and video WhiteRed Red WhiteBlack Black WhiteYellow Yellow SeaTalk devices Red 5 A fused 12 V dc supply Black D11215238 ESeries Widescreen installation37 Alarm connection Typical alarm connectionAn alarm buzzer can be connected using the power data cableprovided with the display Widescreen display 19 way multicable Power data and video Grey Black ve supply Black from battery breaker Red Black Alarm D112162 Note The alarm output is rated for 100 mA maximum loadCables and connections 39High alarm loads and third party alarms 38 GPS connectionYou can use the alarm output to switch a relay This may be useful Depending upon your GPS type it may be either connected viafor connecting high loads such as third party alarm sounders or SeaTalk or NMEA 0183inductive loads to the display If you are in any doubt as to how tomake such connections please consult an authorized installer See alsoThe ESeries Widescreen multifunction display has a positive For SeaTalk connection refer to 36 SeaTalk alarm output The following circuit shows the arrangementfor connection of a relay switch For NMEA 0183 connection refer to 35 NMEA 0183 output configured to switch a relay Alarm out Battery ve Relay Suppression diode High current load D115911 0v return Battery Note When connecting the output to a relay or other inductive device you should fit a spike suppression diode eg 1N400140 ESeries Widescreen installation39 AIS connection Connection using NMEA 0183A compatible AIS can be connected using SeaTalkng or NMEA 0183 1 2 3Connection using SeaTalkng SeaTalkng 1 2 NMEA0183 4800 VHF AIS 500 D1167811 Widescreen display2 AIS500 transceiver NMEA0183 38400 4 D112212 1 VHF antenna 2 VHF radio 3 AIS unit 4 DisplayCables and connections 41310 FastHeading connection Note The connection can be made into any NMEA 0183 input at the displayIf you wish to use MARPA radar target acquisition functions on asystem without an autopilot connected using SeaTalkng then you 1 Multifunction displaywill require a dedicated FastHeading connection The connectionuses NMEA 0183 and is made between a compatible Raymarine 2 Autopilot course or FastHeading sensor and the multifunction display 3 NMEA 0183 FastHeading and other relevant dataThe FastHeading connection is not required if your autopilot isconnected using SeaTalkng 4 Autopilot FastHeading connection 5 Fluxgate compass 1 2 SMARTPILOT NMEA0183 4 3 5 SeaTalk D11220342 ESeries Widescreen SeaTalkng connections Typical SeaTalkng systemThe display can connect as part of a SeaTalkng network ST70 ST70 Instrument Pilot Controller TransducerThe display can use SeaTalkng to communicate with Pod Wind SeaTalkng instruments eg ST70 CANCEL ENTER MENU CANCEL ENTER MENU Transducer SeaTalkng autopilots eg ST70 with SmartPilot SPX course computer Widescreen Display Autopilot Power Supply Course Computer 12 V 24 V dc 12 V dc Data SeaTalkng backbone Transducer Transducer Pod Pod Depth Speed Transducer Transducer D111952Cables and connections 43SeaTalkng cabling 312 NMEA 2000 cables The display can receive data from NMEA 2000 devices eg data from compatible engines The NMEA 2000 connection is made Connection Cable Notes using SeaTalkng and appropriate adaptor cables Backbone cables various lengths The main cable carrying data Spurs You can EITHER from the backbone are used to Use your SeaTalkng backbone and connect each NMEA 2000 connect SeaTalkng devices device on a spur OR Tpiece connectors Used to make junctions in the connect the display on a spur into an existing NMEA 2000 backbone to which devices can then backbone be connected Important You cannot have 2 backbones connected together Terminators Required at either end of the backbone Connecting NMEA 2000 equipment to the SeaTalkng backbone Spur cables Used to connect devices Devices may be daisy chained or connected directly to the Tpieces 1 4Seatalkng power 12V NMEA2000The SeaTalkng bus requires a 12 V power supply This may beprovided from Raymarine equipment with a regulated 12 V supply eg a SmartPilot SPX course computer 3 Other suitable 12 V supply SeaTalkng Note SeaTalkng does NOT supply power to multifunction displays and other equipment with a dedicated power supply input 2 D117111 1 12 V supply into backbone 2 SeaTalkng backbone 3 SeaTalkng to DeviceNet adaptor cable44 ESeries Widescreen installation4 NMEA 2000 equipment 313 Video and alarm audio the display to an existing NMEA 2000 DeviceNet The display supports connection of up to 4 video devices andbackbone an external monitor It also provides an alarm audio output for connection to the vessels audio system Video and alarm audio connection 1 1 2 4 2 3 3 4 1 2 D111982 31 Display 4 52 SeaTalkng to DeviceNet adaptor cable3 DeviceNetng backbone 64 NMEA 2000 equipment D116821Cables and connections 451 Display Composite video connection colors2 Power and data cable Video input Color3 Audio Video cable optional accessory 1 Black4 Video connection 2 Green5 VGA connection to external monitor 3 Blue6 Alarm audio out line level to appropriate amplifier 4 Yellow Note The audio connection is an output only The multifunction display does NOT provide audio inputs If you connect a video Note If your system includes an Infrared thermal imaging device to the multifunction display the associated audio will camera it must be connected to video input 1 only require a separate connection to an external audio system SVideo inputsThe following types of video connection are supported With the optional accessory video audio cable part numberInputs A62158 and optional SVideo adaptor cable part number R08274 Composite video you can connect up to 2 SVideo devices SVideo Each SVideo device requires the equivalent of 2 x video inputs on the display one for the chrominance C signal and another for Note SVideo support requires the latest ESeries Widescreen the luminance Y signal Therefore you can connect a maximum software To check your software version select MENU System of 2 SVideo devices or a combination of SVideo and composite Diagnostics Software Services Unit Info App Version video devices as follows Refer to the Raymarine website for latest 4 x composite devices and no SVideo devices or software versions 2 x SVideo devices orOutputs 1 x SVideo device and up to 2 composite devices VGAComposite inputsWith the supplied power and data cable you can connect 1composite video deviceWith the optional accessory video audio cable you can connect anadditional 3 composite video sources for a total of 4 when used inconjunction with the power and data cable46 ESeries Widescreen connection colors Video input Color SVideo signal Notes 1 1 Power cable Black Chrominance 1 Available on the C1 power cable and SVideo adaptor SVideo adaptor cable White 2 cable R08274 2 Video Alarm cable Luminance 1 Available on the 4 3 1 Green Y1 Video Alarm 2 cable A62158 SVideo adaptor and SVideo 3 cable Yellow adaptor cable 4 R08274 5 3 3 Video Alarm cable Chrominance 2 Available on the Blue C2 Video Alarm cable A62158 SVideo adaptor and SVideo cable White adaptor cable D119311 R08274 1 Power and data cable 4 Video Alarm cable Luminance 2 Available on the 2 Audio Video cable optional accessory Yellow Y2 Video Alarm cable A62158 3 SVideo adaptor cable optional accessory SVideo adaptor and SVideo cable Yellow adaptor cable 4 SVideo connection 1 for example Satellite TV uses display R08274 inputs 1 and 2 5 SVideo connection 2 for example DVD player uses displaySVideo devices are connected as follows inputs 3 and 4 VGA output The VGA output enables you to feed what you see on the multifunction display to an external monitor or television The display output resolution can be adjusted in the Display Setup Menu MENU Display Setup Video Output and connections 47Video and alarm audio cablesThese are the cables which provide connections for video devicesan external monitor and an alarm audio signalVideo and audio cables Cable Part number Notes 15 m 49 ft Power and R62131 Supplied with the data cable display Provides 1 x video input 5 m 164 ft VideoAlarm A62158 Available as an audio cable accessory This cable provides 3 x video input BNC connectors 1 x VGA video output connector 1 x RCA phono jack plug for alarm signalling only Note 5 m 164 ft length is for the VGA flying lead only All other connectors are on leads of 05 m 16 ft length 15 m 49 ft SVideo R08274 Available as an adaptor cable accessory Provides 1 x SVideo input48 ESeries Widescreen 4 Location and contents 41 Selecting a location on page 50 42 Flush mounting on page 52 43 Bracket trunnion mounting on page 53 44 Front bezel on page 55Location and mounting 4941 Selecting a location Water ingress The display is suitable for mounting both above and below decks Warning Potential ignition source It is waterproof to IPX6 standard Although the unit is waterproof it is good practice to locate it in a protected area away from This product is NOT approved for use in prolonged and direct exposure to rain and salt spray atmospheres Do NOT install in a atmosphere such as in an Electrical interference engine room or near fuel tanks Select a location that is far enough away from devices that may cause interference such as motors generators and radio location requirements Magnetic compassWhen selecting a location for your display it is important to considera number of factors Select a location that is at least 3 ft 1 m away from a magnetic compassKey factors which can affect product performance are Power supply Ventilation Select a location that is as close as possible to the boats DC To ensure adequate airflow power source This will help to keep cable runs to a minimum Ensure that equipment is mounted in a compartment of suitable size Adequate space for cooling fins Ensure that ventilation holes are not obstructed Allow Ensure adequate space around the cooling fins in particular you adequate separation of equipment must avoid contact with any metal object or surface Any specific requirements for each system component are Both the cooling fins on the rear of the display and the screws provided later in this chapter securing them MUST NOT be in contact with any metal objects including any metallic part of the vessel structure Failure to adhere Mounting surface to this could result in unwanted current flow and in turn damage Ensure equipment is adequately supported on a secure surface to the vessel structure through the process of galvanic corrosion Do not mount units or cut holes in places which may damage the If this is a concern then the method of mounting must ensure structure of the vessel electrical isolation Cable entry Viewing angle considerations Ensure the unit is mounted in a location which allows proper routing and connection of cables As display contrast color and night mode performance are all affected by the viewing angle Raymarine recommends you Minimum bend radius of 100 mm 394 in unless otherwise temporarily power up the display when planning the installation to stated enable you to best judge which location gives the optimum viewing Use cable supports to prevent stress on connectors angle50 ESeries Widescreen angle Widescreen display dimensions C 80 80 80 B E A D 60 E90W E120W 70 E140W A B C D E D116911 316 mm 197 mm 113 mm 156 mm 211 mm Note The angles are provided for a contrast ratio of equal to CE90W 124 78 44 61 83 or greater than 10 380 mm 245 mm 113 mm 156 mm 260 mm CE120W 15 96 44 61 102 423 mm 277 mm 113 mm 156 mm 291 mm CE140W 167 109 44 61 115 and mounting 5142 Flush mountingThe standard method for mounting the display is a flush or panelmounting mounting the unit ensure that you have Selected a suitable location Identified the cable connections and route that the cables will take Detached the front bezel D111932 1 Check the selected location for the unit A clear flat area with suitable clearance behind the panel is required 2 Fix the appropriate cutting template supplied with the product to the selected location using masking or selfadhesive tape 3 Using a suitable hole saw the size is indicated on the template make a pilot hole in each corner of the cutout area 4 Using a suitable saw cut along the inside edge of the cutout line52 ESeries Widescreen installation5 Ensure that the unit fits into the removed area and then file 43 Bracket trunnion mounting around the cut edge until smooth6 Drill four 45 mm 316 in holes as indicated on the template The display can be mounted on an optional bracket to accept the securing bolts REQUIRES THE OPTIONAL MOUNTING BRACKET ACCESSORY7 Place the gasket onto the display unit and press firmly onto the Before mounting the unit ensure that you have flange8 Connect the power data and other cables to the unit Selected a suitable location9 Slide the unit into place and secure using bolts provided Identified the cable connections and route that the cables will takeOnce you have secured the display in place proceed and attach Attached the front bezelthe front bezelLocation and mounting 53 Note Bracket trunnion mounting kit is available as an optional accessory 1 Mark the location of the mounting bracket screw holes on the chosen mounting surface 2 Drill pilot holes for the screws using a suitable drill taking care that there are no cables or anything that may be damaged behind the surface 3 Use the screws supplied to attach the mounting bracket securely 4 Attach the display unit to the mounting bracket Once you have secured the display in place proceed and make the required cable connections D11191254 ESeries Widescreen installation44 Front bezel 3 Ensure that the control buttons pass through their respective the front bezel 4 Apply firm but even pressure to the bezel along the i Outer edges work from the sides upwards and then alongBefore fitting the bezel you must have mounted the unit in its the top edge to ensure that it clips securely into location ii Inner edges particularly along the chart card door edge to1 Carefully lift one edge of the screen protection film so that it is ensure that the bezel sits flat accessible for removing when unit installation is complete 5 Check that all control buttons are free to operate Use your2 Place the bezel over the front of the display ensuring that the thumb or forefinger in a circular motion to do this clips along the bottom edge of the bezel are latched into position and mounting 55Removing the front bezel The bezel should now come away from the display easily 2 3 1 D111972 Important Use care when removing the bezel Do not use any tools to lever the bezel doing so may cause damage1 Unclip the lower edge of the bezel Starting at the lowercenter edge and working towards the outer edges2 Unclip the left hand edge working from the bottom corner upwards3 Unclip the right hand edge56 ESeries Widescreen 5 System checksChapter contents 51 Initial power on test on page 58 52 Designating the data master on page 59 53 GPS check on page 59 54 Radar check on page 60 55 Sonar check on page 62 56 Thermal camera setup and checks on page 63 57 Language selection on page 64 58 Setting up Autopilot AIS and Navtex on page 65 59 System setup menu on page 66System checks 5751 Initial power on test UniControl The UniControl provides a number of key functions in a overview controlThe touchscreen provides a quick way of performing many 1Some of the functions you can operate with the touchscreen include 2 Accessing applications 3 Adding and editing applications pages Placing and editing waypoints 1 Rotary Control Use this to select menu options and adjust the Building routes value of various items Panning the chart display 2 Trackpad Use this to select menu items options and move the cursor Placing and moving the cursor 3 OK button Use this to confirm a selection or entry Placing and moving VRMs and EBLs Note Raymarine strongly recommends that you familiarize Powering the display on yourself with touch operations while your vessel is anchored 1 Press and hold the POWER button until the Raymarine logo or moored You may find it helpful to use the simulator mode appears accessible from Menu System Setup Menu in these situations 2 Press OK to acknowledge the warning window Note To disable the audible beep that you hear when you touch the screen go to Menu Display Setup Touch beep58 ESeries Widescreen installation52 Designating the data master 53 GPS checkThe following task must be performed on the multifunction displaythat you want to designate as the data master Checking GPS operation1 Press the MENU button You can check that the GPS is functioning correctly using the chart application2 Select the System Setup menu item 1 Select the Chart page3 Select the System Integration menu item4 Select the Data Master ON option5 Press the OK button 2 Check the screen With the chart displayed you should see Your boat position indicates a GPS fix Your current position is represented by a boat symbol or solid circle Your position is also displayed in the data bar under VES POS Note A solid circle on the chart indicates that neither heading nor Course Over Ground COG data is checks 5954 Radar check Typical HD digital radar screen Warning Radar scanner safety Before rotating the radar scanner ensure all personnel are clear Warning Radar transmission safety The radar scanner transmits energy Ensure all personnel are clear of the scanner when the radar is the radar1 Select a Radar page The Radar scanners will now initialize in standby mode this Note The example above is representative of the enhanced process will take approximately 70 seconds output provided by a HD digital radar scanner2 Press the POWER button Points to check3 Press the Radar TxStdby softkey and set to Tx The scanners should now be transmitting and receiving Radar sweep with echo responses are shown on screen4 Check that the radar screen is operating correctly Radar status icon rotating in top right hand corner Check and adjust bearing alignment Bearing alignment The radar bearing alignment ensures that radar objects appear at the correct bearing relative to your boats bow You should check the bearing alignment for any new installation60 ESeries Widescreen misaligned radar Checking the bearing alignment 1 With your vessel under way Align the bow with a stationary 1 2 object identified on the radar display An object between 1 2 NM distant is ideal 2 Note the position of the object on the radar display If the target is not under the ships heading marker SHM there is an alignment error and you will need to carry out bearing alignment adjustment Adjusting the bearing alignment Once you have checked the bearing alignment you can proceed and make any required adjustments With the radar page displayed 1 Select the RADAR SETUP BEARING ALIGNMENT menu 2 Press the BEARING ALIGNMENT softkey 3 Use the rotary control to place the selected target under the Ships Heading Marker 4 Press OK when complete Adjusting radar offset parking This setting is applicable to open array scanners It is used to ensure the scanner parks in the correct position when rotation stops Before you proceed ensure that D115902 The radar page is selected The radar scanner is initialized standby mode Item Description 1 Press the RADAR SETUP SCANNER SETUP 1 Target object such as a buoy dead ahead 2 Select the PARKING OFFSET option then adjust the offset 2 Target displayed on the radar display is not aligned with the angle required to park the radar so that the antenna comes to Ships Heading Marker SHM Bearing alignment is required rest facing forward you should see the Raymarine logo wording from the front of the vessel when you place it in either standby or switch it off 3 Press OK when completeSystem checks 6155 Sonar check 1 Select the fishfinder page Warning Sonar operation NEVER operate the sounder with the boat out of the water NEVER touch the transducer face when the sounder is powered on SWITCH OFF the sounder if divers are likely to be within 76 m 25 ft of the the fishfinder transducerYou must set up the system for the transducer connected to yourDSM Use the fishfinder setup menus to select the 2 Check the fishfinder the fishfinder transducer With the fishfinder active you should seeFrom the main fishfinder screen Depth reading indicates the transducer is working The depth is shown in large white numbers at the bottom left of1 Press the MENU button the screen2 Select Fishfinder Setup from the list of options3 Select Transducer Settings from the list of menu options4 Use the Select Transducer option and select the appropriate transducer from those the sonarSonar checks are made using the fishfinder application62 ESeries Widescreen installation56 Thermal camera setup and checks Panning tilting and zooming the thermal imageTo ensure correct operation of the thermal camera you should setup There are 2 ways of controlling the thermal camera using theand check the cameras main functions thermal proceeding ensure that the camera is connected correctly Using the touchscreen and Range keyaccording to the instructions provided If your system includes theoptional Joystick Control Unit JCU and PoE Power over Ethernet Using the UniControl and Range keyinjector ensure these units are also connected correctly You can pan and tilt the thermal camera using touch actionsSet up the camera Move your finger up and down the screen to tilt the cameraYou will need to up or down Adjust the image aspect ratio contrast brightness and so onCheck the cameraYou will need to Check the camera movement pan tilt zoom Check the camera home position is appropriate Move your finger left and right on the screen to rotate the camera left or right the thermal video aspect ratioIn the thermal camera application1 Select the OPTIONS softkey2 Select the PRESENTATION softkey3 Use the ASPECT RATIO softkey to select the Auto 43 or 169 option as appropriate Note You cannot zoom the thermal camera image using the touchscreen You must use the multifunction displays Range keyAdjusting the thermal camera image see below or the thermal cameras optional Joystick ControlInthe thermal camera application Unit JCU1 Select the OPTIONS softkey You can also use a combination of the UniControl and range keys2 Select the PRESENTATION softkey to manipulate the thermal camera view This method is ideal for3 Select the CONTRAST BRIGHTNESS or COLOR softkey as finer control over the camera and is particularly useful in rough sea appropriate conditions4 Using the trackpad adjust the level as requiredSystem checks 63 UniControl is used for rotating the camera left or right 57 Language selection panning or tilting the camera up or down The system can operate in the following languages English US English UK Chinese Danish Dutch Finnish Range key is used to zoom in and out French German Greek Italian Japanese Korean Norwegian Portuguese Brazilian the thermal camera to the home Spanish Swedish Polish CroatianIn the thermal camera application 1 Press the MENU button to open the setup menu1 Select the CAMERA HOME softkey 2 Select the System Setup Language menu The camera returns to its currently defined home position and 3 Select from the languages available the Home icon appears onscreen momentarily64 ESeries Widescreen installation58 Setting up Autopilot AIS and NavtexSome setting up is required to enable integration of Autopilot AISand Navtex equipment connected as part of your system1 Check the system integration settings i Access the Menu System Setup System Integration menu ii Autopilot control This option should be Enabled if you wish to control a compatible autopilot using the display iii NMEA port settings These should be set appropriately for the connected devices iv Bridge NMEA heading This should be set ON only if the display is used as a source of heading data for other devices connected on SeaTalk or SeaTalkng2 Check the display presentation settings The AIS presentation layer must be turned ON in order to display targets i Select the 2D Chart Layers from the chart window ii Select AIS Targets On or Off as changes to the system set up can be made as most other equipment will operate to a default level withoutfurther checks 6559 System setup menuThe following table describes the various options in the System Setup menu for your multifunction display Menu item Description Options Boat Details The accurate operation of the collision alarm is dependent on Minimum Safe Depth you supplying suitable values for the Boat Details setting You should specify the minimum safe depth beam and height for Minimum Safe Beam your vessel The values you specify MUST be appropriate for Minimum Safe Height safe navigation and must also take into account the position of the GPS antenna on your vessel as the collision alarm uses data from the GPS antenna Position Mode Determines how positioning data is displayed as Latitude Lat Long default Longitude coordinates or Loran TDs TDs TD Setup When the Position Mode see above is set to TDs you can Chain specify the chain identifier slave and ASF values Various options depending on cartography Slave 12 Various options depending on cartography ASF 12 099 to 099 Simulator Enables or disables simulator mode which allows you to practice OFF default operating your multifunction display without data from a GPS antenna fishfinder DSM sonar or any other external unit ON DEMO Simulator Speed Enables you to specify the speed at which the vessel icon will 1x move when the Simulator mode is enabled see above 2x 3x66 ESeries Widescreen installation Menu item Description Options Bearing Mode Determines how all bearing and heading data is displayed in True default This does not affect how the chart or radar displays are drawn Magnetic MOB Data Type Determines whether positional data or dead reckoning is Dead Reckoning displayed Assuming that your vessel and the Man Overboard MOB are subject to the same tide and wind effects the dead Position default reckoning setting normally gives a more accurate course Variation Source This setting compensates for the naturally occuring offset Auto compensation value displayed in of the earths magnetic field When set to Auto the system brackets default automatically compensates and displays the compensation value in brackets To enter your own compensation value use Manual the Manual option then specify the value using the Manual Variation setting see below Manual Variation When the Variation Source menu item is set to Manual see 0 degrees East default above you use the Manual Variation setting to specify the compensation value that you want to use This value is also Range 0 to 30 degrees East or West transmitted to any other connected Raymarine instruments Language Determines the language that will be used for all onscreen text labels menus and options Ground Trip Reset Resets the chosen ground trip distance counter to zero Ground Trip 1 Reset Ground Trip 2 Reset Ground Trip 3 Reset Ground Trip 4 Reset Settings Reset Resets all system setup menus including page sets and the Reset Defaults confirmation databar to the factory default settings Waypoints routes and tracks are NOT deleted YES NOSystem checks 67 Menu item Description Options Settings and Data Reset Resets all system setup menus including page sets and the Factory Reset confirmation databar to the factory default settings Waypoints routes and tracks ARE deleted YES NO Note For systems using multiple multifunction displays networked displays the complete system database is deleted on the data master primary display Only the waypoints routes and tracks will be deleted from any additional multifunction displays Note If this reset function is performed on a GSeries system it will also delete your Nav Station settings Time Date Setup These options enable you to customize the time and date format Date Format to your requirements You can also specify a local time offset from Universal Time Constant UTC to compensate for any mmddyy time zone difference ddmmyy Time Format 12 hr 24 hr Local Time Offset 0130 to 013068 ESeries Widescreen installation Menu item Description Options Units Setup Enables you to specify the units used for the following key Distance Units measurements Nautical Miles default Distance Statute Miles Speed Kilometers Depth Speed Units Temperature Knots default Pressure mph miles per hour Volume kph kilometers per hour Note If the Distance unit is set to Nautical Miles or Statute Depth Units Miles and the data displayed is less than 1 unit the system displays the units in Feet If the Distance unit is set to Meters Kilometers the system displays the units in Meters Feet default Fathoms Temperature Units Fahrenheit default Celsius Pressure Units Bar PSI default Kilopascals Volume Units US Gallons Imp Imperial Gallons defaultSystem checks 69 Menu item Description Options Liters System Integration Determines the connection settings for external equipment The Autopilot Control following items are available in the submenu Disabled default Autopilot Control If set to Enabled this option allows you to control certain aspects of a connected pilot control head Enabled such as sending commands to engage and disengage the DSC Message autopilot If set to Disabled you will not be able to control the autopilot from your multifunction display and all functions OFF must be controlled from the pilot control head itself ON default DSC Message If set to ON details of distress DSC SeaTalk Alarms messages from a connected DSC VHF radio will be displayed on your multifunction display If set to OFF the messages will ON default NOT be displayed on your multifunction display OFF SeaTalk Alarms If set to ON all system alarms generated by any connected SeaTalk units will be displayed on your Preferred GPS Source multifunction display If set to OFF the alarms will NOT be displayed on your multifunction display SeaTalkng NMEA2000 default Preferred GPS Source Your multifunction display SeaTalk1 supports GPS receivers connected by SeaTalk1 SeaTalkng NMEA0183 or NMEA2000 Select the preferred source Data Master Data Master If you have more than one multifunction display on the same network one of them must be set as the ON default data master When this option is set to ON the multifunction OFF display you are currently using will be set as the data master Bridge NMEA Heading Bridge NMEA Heading If set to ON NMEA heading data will be bridged onto the SeaTalk data bus and will be sent to OFF default all NMEAconnected devices If set to OFF NMEA heading data will NOT be bridged onto the SeaTalk bus An example ON of a use for this setting is when using MARPA with an external Keyboard fast heading sensor in which case you should set this option70 ESeries Widescreen installation Menu item Description Options to OFF to ensure that all NMEAconnected units receive heading data from the external heading sensor OFF Keyboard Set to ONE or ALL if you have an external ALL default keyboard connected Otherwise set to OFF ONE NMEA Output Setup allows you to enable or disable the NMEA Output Setup individual NMEA output sentences for each NMEA port APB NMEA Port Setting Allows you to specify the appropriate port speed for the equipment connected to each NMEA port BWC When the Navtex 4800 or Navtex 9600 option is selected you will be able to view the Navtex message list Use the AIS BWR 38400 option for AIS receivers DBT DPT GGA GLL GSA MTW MWV RMA RMB RMC RSD RTE TTM VHW VLWSystem checks 71 Menu item Description Options WPL VTG ZDA NMEA Port Setting NMEA 4800 default Navtex 4800 Navtex 9600 AIS 38400 Waypoint Password Setup This menu allows you to enable password protection for Enable Password waypoints and to change the password OFF default ON Change Password Displays Edit Waypoint Password dialog72 ESeries Widescreen 6 contents 61 on page 74 62 Power up on page 75 63 Radar on page 76 64 GPS on page 77 65 Sonar on page 78 66 Thermal camera on page 79 67 System data on page 82 68 Video on page 83 69 Touchscreen on page 84 610 SeaTalkhs LED indications on page 85 611 Miscellaneous on page 7361 information provides possible causes andcorrective action required for common problems associated withmarine electronics Raymarine products are prior to packing and shipping subjectedto comprehensive test and quality assurance programs Howeverif you experience problems with the operation of your multifunction display this section will help you todiagnose and correct problems in order to restore normal operationIf after referring to this section you are still having problems with yourunit please contact Raymarine Technical Support for further advice74 ESeries Widescreen installation62 Power up at power up and their possible causes and solutions are described here Problem Possible causes Possible solutions The system or part of it does not start up Power supply problem Check relevant fuses and breakers Check that the power supply cable is sound and that all connections are tight and free from corrosion Check that the power source is of the correct voltage and sufficient 7563 Radar with the radar and their possible causes and solutions are described here Problem Possible causes Possible solutions No Data or No scanner message Radar scanner power supply Check that the scanner power supply cable is sound and that all connections are tight and free from corrosion Check relevant fuses and breakers Check power source is of the correct voltage and sufficient current using voltage booster if appropriate SeaTalkhs network problem Check that the Scanner is correctly connected to a SeaTalkhs switch or crossover coupler as applicable Check the status of the SeaTalkhs switch Check that SeaTalkhs cables are free from damage Software mismatch between equipment Contact Raymarine technical support may prevent communication Switch at scanner pedestal in OFF Ensure scanner pedestal switch is in ON position position Radar will not initialize Voltage control Intermittent or poor power connection Check power connection at VCM Voltage at input 12 24 V Voltage module VCM stuck in sleep mode at output 40 V The bearing of a target on the radar The radar bearing alignment requires Check and adjust radar bearing alignment screen is incorrect correcting76 ESeries Widescreen installation64 GPS with the GPS and their possible causes and solutions are described here Problem Possible causes Possible solutions No Fix GPS status icon is displayed Geographic location or prevailing Check periodically to see if a fix is obtained in better conditions or another conditions preventing satellite fix geographic location External GPS connection fault Ensure that GPS connections and cabling are correct and fault free External GPS antenna in poor position Ensure GPS antenna has a clear view of the sky For example Below decks Close proximity to transmitting equipment such as VHF radio GPS installation problem Refer to manufacturers handbook for installation details Note A GPS Status screen is available within the Setup menu This provides satellite signal strength and other relevant 7765 Sonar with the sonar and their possible causes and solutions are described here Problem Possible causes Possible solutions No data source for the fishfinder DSM power supply fault Check the DSM power supply and cables Other DSM fault Refer to the instructions supplied with the DSM unit SeaTalkhs network problem Check that the DSM is correctly connected to the a SeaTalkhs switch or crossover coupler as applicable Check the status of the SeaTalkhs switch if applicable Check that SeaTalkhs cables are free from damage Software mismatch between equipment Contact Raymarine technical support may prevent communication Problematic depth readings or sonar Gain or Frequency settings may be Check the fishfinder presets gain and frequency settings image inappropriate for present conditions DSM cable fault Ensure that the power transducer and all other cables to the DSM unit are properly connected and free from damage Other DSM fault Refer to the instructions supplied with the DSM unit78 ESeries Widescreen installation66 Thermal camera with the thermal camera and their possible causes and solutions are described here Problem Possible causes Possible solutions Video not displayed Camera is in Standby mode The camera will not display video if it is in Standby mode Use the camera controls either the thermal camera application or JCU to wake the camera from standby Problem with the thermal camera video Check thermal camera video cables are sound and properly connected connections Ensure that the video is connected into video input 1 at the multifunction display or GVM Ensure that the correct video input is selected at the display Problem with power supply to the camera Check the power connections to the camera and JCU PoE injector if or JCU if used as the primary controller used Ensure that the power switch breaker is on Check the fuse breaker state Cannot control thermal camera from Thermal camera application is not running Ensure the thermal camera application is running on the multifunction Raymarine display or keyboard display as oppose to the video application which does not have camera 79 Problem Possible causes Possible solutions Erratic or unresponsive controls SeaTalkhs problem Check that the controller and thermal camera are correctly connected to the SeaTalkhs network Note This may be a direct connection or via a SeaTalkhs switch Check the status of the SeaTalkhs switch Check that SeaTalkhs cables are free from damage Control conflict eg caused by multiple Ensure that no other controllers are in use at the same time users at different stations Problem with the controller Check power SeaTalkhs cabling to the controller and PoE injector PoE only used with optional Joystick Control Unit Check other controllers if available If other controllers are operating this will eliminate the possibility of a more fundamental camera fault Cannot switch between thermal and Camera is not a dual payload model Only dual payload dual lens thermal cameras support VIS IR switching visible VIS IR video image VIS IR cable not connected Ensure that the VIS IR cable is connected from the camera to the Raymarine system The IRonly cable does not support switching Noisy image Poor quality or faulty video cable Ensure that the video cable is no longer than necessary The longer the cable is or the smaller the wire gauge thickness the more severe the losses become Use only high quality shielded cable suitable for a marine environment Cable is picking up Ensure you are using a high quality shielded cable interference EMI from another device Ensure proper cable separation for example do not run data and power cables in close proximity with each other80 ESeries Widescreen installation Problem Possible causes Possible solutions Image too dark or too light Display brightness is set too low Use the brightness controls at the display to adjust accordingly The contrast or brightness settings in the Use the appropriate softkeys in the thermal camera application to adjust the thermal camera application are set too contrast and brightness of the image low The Scene Mode is not appropriate for the A particular environment may benefit from a different Scene Mode setting current conditions For example a very cold background such as the sky could cause the camera to use a wider temperature range than appropriate Use the SCENE button Image freezes momentarily FFC Flat Field Correction The image will pause momentarily on a periodic basis during the Flat Field Correction FFC cycle Just prior to the FFC a small green square will appear in the upper left corner of the screen Image is inverted upside down Camera Ball down setting is incorrect Ensure that the Ball down setting within the thermal camera system setup menu is set 8167 System data of the installation can cause problems with the data shared between connected equipment Such problems their possiblecauses and solutions are described here Problem Possible causes Possible solutions Instrument engine or other system data is Data is not being received at the display Check the data bus eg SeaTalkng wiring and connections unavailable at all displays Check the overall integrity of the data bus eg SeaTalkng wiring If available refer to the reference guide for the data bus eg SeaTalkng reference manual Data source eg ST70 instrument or Check the source of the missing data eg ST70 instrument or engine engine interface is not operating interface Check the power to the SeaTalk bus Refer to the manufacturers handbook for the equipment in question Software mismatch between equipment Contact Raymarine technical support may prevent communication Instrument or other system data is missing SeaTalkhs network problem Check that all required equipment is connected to the SeaTalkhs switch from some but not all displays Check the status of the SeaTalkhs Switch Check that SeaTalkhs cables are free from damage Software mismatch between equipment Contact Raymarine technical support may prevent ESeries Widescreen installation68 Video with the video inputs and their possible causes and solutions are described here Problem Possible causes Possible solutions No signal message on screen video Cable or connection fault Check that the connections are sound and free from corrosion image not displayed Only 1 video connection available Video inputs 2 3 and 4 are on a separate Ensure that you have the separate audiovideo cable and that it is correctly audio video cable 8369 Touchscreen with the touchscreen and their possible causes and solutions are described here Problem Possible causes Possible solutions Touchscreen does not operate as Touch lock is enabled Use the Trackpad to turn off the touch lock on the home screen expected Screen is not being operated with bare Bare fingers must make contact with the screen for correct operation fingers for example gloves are being worn Alternatively you may use conductive gloves Touchscreen requires calibration Use the setup menus to calibrate the touchscreen Saltwater deposits on the screen Carefully clean and dry the screen in accordance with the instructions provided84 ESeries Widescreen SeaTalkhs LED indicationsLED indications associated with the SeaTalkhs switch are describedhere LED state Possible causes For all connected channels 1 steady No problem detected Steady LED and 1 flashing green LED indicates network connection Flashing LED indicates network traffic No LEDs are illuminated No power to the SeaTalkhs switch Some LEDs are not illuminated Cable connection faults on the channels with nonilluminated LEDs Equipment connected to nonilluminated LEDs may be 85611 Miscellaneous problems and their possible causes and solutions are described here Problem Possible causes Possible solutions Display behaves erratically Intermittent problem with power to the Check relevant fuses and breakers display Frequent unexpected resets Check that the power supply cable is sound and that all connections are tight and free from corrosion System crashes or other erratic behavior Check that the power source is of the correct voltage and sufficient current Buttons trapped by front bezel Ensure that the front bezel is fitted correctly and that all buttons are free to operate correctly Software mismatch on system upgrade Go to and click on support for the latest software required downloads Corrupt data other unknown issue Perform a factory reset This option can be found within Menu System Setup Settings and Data Reset Important This will result in the loss of any settings and data such as waypoints stored on the display Please save any important data to a CF card before resetting86 ESeries Widescreen 7 Technical supportChapter contents 71 Raymarine customer support on page 88 72 3rd party support on page 89Technical support 8771 Raymarine customer support Viewing multifunction display software provides a comprehensive customer support serviceYou can contact customer support through the Raymarine website 1 Press the MENU and email If you are unable to resolve a problem please 2 Select System Diagnosticsuse any of these facilities to obtain additional help 3 Select Software ServicesWeb support 4 Select Unit InfoPlease visit the customer support area of our website at A range of information is displayed including the App software versionThis contains Frequently Asked Questions servicing access to the Raymarine Technical Support Department anddetails of worldwide Raymarine and email supportIn the USA Tel 1 603 881 5200 extension 2444 Email the UK Europe the Middle East or Far East Tel 44 023 9271 4713 Email informationIf you need to request service please have the following informationto hand Product name Product identity Serial number Software application versionYou can obtain this product information using the menus within yourproduct88 ESeries Widescreen installation72 3rd party supportContact and support details for 3rd party suppliers can be found onthe appropriate marine support 8990 ESeries Widescreen 8 Technical contents 81 Technical specification on page 92Technical specification 9181 Technical specification Environmental Installation environment Nominal supply voltage 12 or 24 V dc Operating temperature 10 C to 50 C 14 F to 122 F Operating voltage range 107 to 32 V dc Storage temperature 20 C to 65 C 4 F to 149 F Fuse Breakers Inline fuse fitted within power cable Relative humidity max 95 7 A Standard 20 mm glass fuse Water proof to IPX6 Weight E90W 37 kg 82 lb E120W 44 kg 97 lb E140W 54 kg 119 lb Display screen TFT LCD display 24bit color 167 M Current 4 A peak operating current colors Power consumption Typical power consumption at full Resolution brightness E90W 9 in display 800 x 480 E90W 23 W pixels E120W 35 W E120W 12 in display 1280 x 800 pixels E140W 37 W E140W 14 in display 1280 x 800 LEN 1 pixels Refer to Seatalkng reference manual for further information Brightness E90W 800 cdm2 E120W E140W 1000 cdm292 ESeries Widescreen installation Data connections 3 x NMEA 0183 ports Electronic charts Embedded electronic charts NMEA port 1 IO 48009600 Navionics embedded cartography baud appropriate to purchase region North America Europe or Rest of NMEA port 2 IO World as appropriate 4800960038400 baud Compatible chart cards NMEA port 3 Input only 4800 CompactFlash baud Navionics Silver Gold Gold 1 x SeaTalk port Platinum and Platinum 1 x SeaTalkhsport 100 Mbitss RJ45 type connection Conformance Europe 2004108EC 1 x SeaTalkng connection Australia and New Zealand CTick Compliance Level 2 Audio alarm output 1 x Alarm output Provides supply battery voltage 100 mA peak load 1x Alarm repeat Line level output 1V rms line level into 600R load Video input 4 x NTSCPAL video inputs to ITUR BT601 standard Video output 1 x VGA output at either 720p 1280 x 720 or native display specification 9394 ESeries Widescreen 9 Options and contents 91 SeaTalk accessories on page 96 92 SeaTalkng accessories on page 96 93 SeaTalkhs accessories on page 97 94 Spares and accessories on page 99Options and accessories 9591 SeaTalk accessories 92 SeaTalkng cables and accessories for use with compatible products SeaTalkng cables and accessories for use with compatible products Description Part No Notes Description Part No Notes NMEA SeaTalk E85001 Backbone Kit A25062 Includes converter 2 x 5 m 164 ft 3 m 98 ft SeaTalk D285 Backbone cable extension cable 1 x 20 m 656 ft 5 m 164 ft SeaTalk D286 Backbone cable extension cable 4 x Tpiece 9 m 295 ft SeaTalk D287 extension cable 2 x Backbone terminator 12 m 394 ft SeaTalk E25051 extension cable 1 x Power cable 20 m 656 ft SeaTalk D288 SeaTalkng 04 m 13 ft A06038 extension cable spur SeaTalkng 1 m 33 ft A06039 spur SeaTalkng 3 m 98 ft A06040 spur SeaTalkng 5 m 164 ft A06041 spur SeaTalkng 04 m 13 ft A06033 backbone SeaTalkng 1 m 33 ft A06034 backbone SeaTalkng 3 m 98 ft A06035 backbone96 ESeries Widescreen installation Description Part No Notes 93 SeaTalkhs accessories SeaTalkng 5 m 164 ft A06036 Digital radar scanner cables backbone Scanner cables SeaTalkng 20 m 656 ft A06037 backbone Connect the Radar scanner to either the SeaTalkhs switch or the crossover coupler SeaTalkng bare ends 1 A06043 m 33 ft spur Cable Part number Notes SeaTalkng bare ends 3 A06044 5 m 164 ft Digital cable A55076 m 98 ft spur 10 m 328 ft Digital A55077 Your radar scanner may SeaTalkng SeaTalk2 A06048 cable include the 10 m cable 04 m 13 ft spur depending upon the model purchased SeaTalkng Power cable A06049 15 m 492 ft Digital A55078 SeaTalkng Terminator A06031 cable SeaTalkng TPiece A06028 Provides 1 x spur 25 m 820 ft Digital A55079 connection cable SeaTalkng 5way A06064 Provides 3 x spur connector connections Scanner extension cables SeaTalkng Blanking plug A06032 Use of one of these cables to extend the connection between the radar scanner and the SeaTalkhs switch or crossover coupler Cable Part number Notes 25 m 82 ft extension A92141 cable 5 m 164 ft extension A55080 cable 10 m 328 ft extension A55081 cableOptions and accessories 97SeaTalkhs network cables SeaTalkhs network cables Cable Part number NotesStandard network cables connect compatible equipment to the SeaTalkhs switch E55058 8 way hub for switch or crossover coupler they have a waterproof connection of at one end SeaTalkhs devices Cable Part number Notes SeaTalkhs coupler E55060 Couple for connection of a single SeaTalkhs SeaTalkhs 15 m 49 ft E55049 device network cable 5 m 164 ft SeaTalkhs E55050 network cable 10 m 328 ft SeaTalkhs E55051 network cable 20 m 656 ft SeaTalkhs E55052 network cableFully waterproof SeaTalkhs network cablesConnect directly from display to display Cable Part number Notes 15 m 49 ft Dual end A62245 Cable has waterproof SeaTalkhs network cable connectors at both ends 15 m 492 ft Dual end A62246 Cable has waterproof SeaTalkhs network cable connectors at both ends98 ESeries Widescreen installation94 Spares and accessories Description Part No NotesOptions and accessories for the ESeries Widescreen Trunnion bracket A62134 mount kit C140W Optional accessories E140W 5 m 164 ft AudioVideo A62158 Available as an Description Part No Notes cable accessory This cable provides Trunnion bracket A62132 mount kit C90W 3 x video input BNC E90W connectors Trunnion bracket A62133 1 x VGA video output mount kit C120W connector E120W 1 x RCA phono jack plug for alarm signalling only Note 5 m 164 ft length is for the VGA flying lead only All other connectors are on leads of 05 m 16 ft length Spare replacement parts Description Part No Notes Trunnion knob R08001 Suncover C90W R62122 E90WOptions and accessories 99 Description Part No Notes Description Part No Notes Suncover C120W R62123 Seal Set C120W R62187 E90W E120W Suncover C140W R62124 Seal Set C140W R62188 E90W E140W Flushmount Gasket C R62128 Front panel C90W R62191 and EWidescreen all E90W models Front panel C120W R62192 Flushmount Screw Kit R62312 E120W C and EWidescreen all models Front panel C140W R62193 E140W Bezel E90W R62151 Chartreader assembly R62209 Bezel E120W R62152 Lower keyboard assy R62211 Bezel E140W R62153 C90W E90W 15 m 49 ft Power and R62131 Lower keyboard assy R62212 data cable straight C120W E120W 15 m 49 ft Power and R62227 Lower keyboard assy R62213 data cable 90 degree C140W E140W Side keyboard assy R62214Service sparesService spares are available to service dealers only E90W Bonded R62249 Touchscreen Assembly Description Part No Notes E120W Bonded R62250 Touchscreen Assembly Chart door R62184 E140W Bonded R62251 Seal Set C90W E90W R62186 Touchscreen Assembly100 ESeries Widescreen installation Description Part No Notes Rotary encoder PCB R62252 assembly IO PCB Assembly R62253 CPU PCB Assembly R62254 Keymat Set R62270 SSD PCB Assembly R62255 US version SSD PCB Assembly R62298 EU version SSD PCB Assembly R62299 ROW version UniControl R62313Options and accessories 101102 ESeries Widescreen A Multifunction display Your multifunction display uses a number of protocols to transfer data between the various devices in your networked system Thesystem integration following table details which devices may be connected to your display and the type of connectivity in terms of protocols andYou can connect a number of external devices to your multifunction physical providing additional features and functionsThe following diagram illustrates the various external devices thatcan be connected to your multifunction display Instruments VideoCamera External GPS Thermal camera Autopilot ESeries display DSC VHF Digital Open Array radar scanner 11180 RAY240 or Digital Radome scanner AIS receiver transceiver Personal Fishfinder SeaT alkhs Additional Computer DSM30 300 or 400 switch ESeries displays Weather receiver display system integration 103 Device Type Suitable Devices Connectivity Device Type Suitable Devices Connectivity Radar Up to two Raymarine SeaTalkhs of ONE of the following radar scanners may Raymarine fishfinders be connected to your DSM 30 multifunction display but only one may be DSM 300 operated at any one time DSM 400 Cartography included Embedded internal Internal storage 4 kilowatt Digital Navionics cartography Radome Scanner 4 kilowatt HD Digital Cartography optional External CompactFlash Card slot Radome Scanner microSD or microSDHC chart cards Note microSD 4 kilowatt HD Digital and microSDHC Open Array Scanner Navionics Silver cards require the Navionics Gold optional Raymarine 12 kilowatt HD Digital CF microSD card Open Array Scanner Navionics Gold adaptor Only the 4 kilowatt SuperHD official Raymarine Navionics Platinum adaptor is compatible Digital Open Array Scanner Navionics Platinum with your system 12 kilowatt SuperHD Navionics FishN Chip Digital Open Array Navionics Hotmaps Scanner Refer to the Note Please Raymarine website ensure your radar scanner is using for the latest list of the latest software supported chart cards version Sirius WeatherAudio Raymarine SR100 SeaTalkhs Fishfinder The ESeries SeaTalkhs Sirius Weather Widescreen display Receiver supports the connection104 ESeries Widescreen installation Device Type Suitable Devices Connectivity Device Type Suitable Devices Connectivity AIS The ESeries NMEA 0183 or Thermal camera The ESeries SeaTalkhs for control Widescreen display SeaTalkng Widescreen display BNC connector for supports the connection supports the connection video of ONE of the following of ONE of the following AIS units Raymarine thermal cameras Raymarine AIS 250 T300 thermal camera Raymarine AIS 500 9 Hz Thirdparty AIS Class T303 thermal camera A or Class B receiver 30 Hz transceiver T350 thermal camera Navtex Navtex Receiver NMEA 0183 9 Hz Fast Heading Sensor Fast Heading Sensor NMEA 0183 T400 thermal camera GPS external Raystar125 GPS or SeaTalk SeaTalkng or 9 Hz thirdparty external GPS NMEA 0183 T403 thermal camera receiver 30 Hz Instruments All current Raymarine SeaTalk SeaTalkng or T450 thermal camera instruments NMEA 0183 9 Hz Autopilot Raymarine All current Raymarine SeaTalk SeaTalkng Video camera Composite or SVideo BNC connector autopilots PAL or NTSC video source Autopilot third party Thirdparty autopilots NMEA 0183 waypoint and bearing information VHF radio Raymarine DSC VHF NMEA 0183 SeaTalk radios Additional multifunction E90W E120W E140W SeaTalk SeaTalkhs displays GSeries displays display system integration 105Appendix B NMEA 0183 sentences Recommended minimum specific RMC GPS transit dataThe display supports the following NMEA 0183 sentences Theseare applicable to NMEA 0183 and SeaTalk protocols VTG Course over ground and ground speed ZDA Time and dateTransmit APB Autopilot b MWV Wind speed and angle BWC Bearing and distance to waypoint RTE Routes sentence Bearing and distance to waypoint WPL Waypoint location sentence BWR rhumb line Receive DBT Depth below transducer AAM Waypoint arrival alarm sentence DPT Depth DBT Depth below transducer sentence MTW Water temperature DPT Depth sentence Recommended minimum navigation RMB information DTM Datum reference sentence RSD Radar system data APB Autopilot b sentence TTM Tracked target message Bearing and distance to waypoint VHW Water speed and heading BWC sentence VLW Distance travelled through the water Bearing and distance to waypoint BWR rhumb line sentence GGA Global positioning system fix data Digital selective calling information GLL Geographic position latitude longitude DSC sentence GSA GPS DOP and active satellites DSE Distress sentence expansion GSV GPS satellites in view Global positioning system fix data Recommended minimum specific GGA sentence RMA loran c data Geographic position loran c sentence GLC106 ESeries Widescreen installation Geographic position latitude longitude ZDA Time and date sentence GLL sentence MDA Meteorological composite sentence GPS DOP and active satellites GSA sentence GPS satellite fault detection data GBS sentence GSV GPS satellites in view sentence RTE Routes sentence Heading deviation and variation HDG sentence WPL Waypoint location sentence HDT Heading true sentence HDM Heading magnetic sentence MSK MSK receiver interface sentence MSS MSK receive r signal status sentence MTW Water temperature sentence WMV Wind speed and angle sentence Recommended minimum specific RMA loran c data sentence Recommended minimum navigation RMB information sentence Recommended minimum specific RMC GPS transit data sentence VHW Water speed and heading sentence Distance travelled through the water VLW sentence Course over ground and ground speed VTG sentence XTE Cross track error measured sentenceNMEA 0183 sentences 107Appendix C NMEA 2000 sentencesThe display supports the following NMEA 2000 sentences These are applicable to NMEA 2000 SeaTalkng and SeaTalk 2 protocols Message number Message description Transmit Receive Bridge 59392 ISO Acknowledgment 59904 ISO Request 60928 ISO Address Claim 126208 NMEA Acknowledge group function 126464 PGN List 126992 System time 126996 Product information 127237 HeadingTrack Control 127245 Rudder 127250 Vessel heading 127488 Engine parameters rapid update 127489 Dynamic engine parameters 127493 Dynamic transmission 127498 Static engine parameters 127505 Fluid level 128259 Speed 128267 Water depth 128275 Distance log 129025 Position rapid update 108 ESeries Widescreen installation Message number Message description Transmit Receive Bridge 129026 COG SOG rapid update 129029 GNSS position data 129033 Time and date 129038 AIS Class A Position Report 129039 AIS Class B Position Report 129040 AIS Class B Extended Position Report 129044 Datum 129283 Cross track error 129284 Navigation data 129291 Set and drift rapid update 129301 Time to or from mark 129539 NMEA 2000 GNSS DOPs message 129540 GNSS Sats in view 129545 NMEA 2000 GNSS RAIM output message 129550 GNSS differential correction receiver interface 129551 GNSS differential correction receiver signal 129793 AIS UTC and Date Report 129794 AIS Class A Static and Voyage Related Data 129801 AIS Addressed Safety Related Message 129802 AIS Safety Related Broadcast Message 130306 Wind data NMEA 2000 sentences 109 Message number Message description Transmit Receive Bridge 130310 Environmental parameters 130311 Environmental parameters message 130576 Small craft status 130577 Direction data 130578 Vessel speed components 110 ESeries Widescreen D Connectors and pinouts Signal Pin Cable AWG Grouping ColorPower data and video connector NMEA1 6 7015 26 Twisted Yello TX pair 1 2 3 4 5 6 NMEA1 9 7015 26 Brown 7 8 9 10 TX 11 12 18 19 NMEA1 4 7015 26 Twisted White 13 14 15 16 RX pair 17 NMEA1 8 7015 26 Green RX Item Remarks NMEA2 1 7015 26 Twisted Orange Identification PWRNMEASTVideo TX pair Yellow Connector type 19 pin twistlock NMEA2 3 7015 26 Orange TX Brown Current source to network No current sourced for external devices NMEA2 7 7015 26 Twisted Orange RX pair White Current sink from network PSU Main Power input NMEA No power required for NMEA2 11 7015 26 Orange interface RX Green ST1 50mA Interface drive only NMEA3 5 7015 26 Twisted Blue RX pair White Video No power required for interface NMEA3 2 7015 26 Blue RX GreenPower data and video cable cores and colors ST1 10 7015 26 White BATT Red Signal Pin Cable AWG Grouping Color ST1 DATA 12 7015 26 White BATT 18 3202 18 Red Yellow BATT 19 3202 18 Black HONK 16 7015 26 Grey SCREEN 17 not usedConnectors and pinouts 111 Signal Pin Cable AWG Grouping Color Pin Signal ST1 14 7015 26 White 8 VIDEO OUT HSYNC BATT Black 9 VIDEO OUT VSYNC VIDEO 15 RG179 75R coax 10 AUDIO OUT or equiva 11 VIDEO OUT RED lent 12 VIDEO OUT HSYNC GROUND VIDEO 13 Screen RTN 13 VIDEO OUT RED GROUND 14 VIDEO OUT VSYNC GROUNDVideo and alarmaudio for the connector providing video and alarm audio 15 16 VIDEO OUT GREEN 1 2 17 SHIELD 3 4 5 7 8 6 18 VIDEO OUT GREEN GROUND 11 9 10 12 13 14 15 19 VIDEO OUT BLUE 16 17 20 18 19 20 VIDEO OUT BLUE GROUND Pin Signal SeaTalkhs connector 1 VIDEO IN A 1 8 2 VIDEO IN B 3 VIDEO IN C 4 VIDEO IN B RETURN 5 VIDEO IN A RETURN 6 VIDEO IN C RETURN 7 AUDIO OUT 112 ESeries Widescreen installation Item Remarks Item Remarks Identification ST2NMEA2000 Identification STHS Connector type STNG Connector type RJ45 with suitable waterproofing Current source to network No current sourced for external devices Current source to network No current sourced for external devices Current sink from network 160mA Interface drive only Current sink from network No power required for interface Pin Signal Pin Signal 1 12V 1 Tx 2 0V 2 Tx 3 Screen 3 Rx 4 CanH 4 Not connected 5 CanL 5 Not connected 6 SeaTalk not connected 6 Rx 7 Not connected Note Use only Raymarine cables when connecting to SeaTalkng 8 Not connected Note Use only Raymarine cables when connecting to connector 5 1 6 4 2 3Connectors and pinouts 113wwwra ym a rin e c o m


NOTICE: Some pages have affiliate links to Amazon. As an Amazon Associate, I earn from qualifying purchases. Please read website Cookie, Privacy, and Disclamers by clicking HERE. To contact me click HERE. For my YouTube page click HERE