L-36.com

Raymarine G Series Gvm400 Installation Guide 87068 2


Note: This is the new High Definition version of the Manual viewer with 4x the number of pixels per page.
Some manual pages may be blank. There will be an End of File notice after the last page.

Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.
GVM400video and patents noticeAutohelm hsb2 RayTech Navigator Sail Pilot SeaTalk SeaTalkNG SeaTalkHS and Sportpilot are registered trademarks of RaymarineUK Limited RayTalk Seahawk Smartpilot Pathfinder and Raymarine are registered trademarks of Raymarine Holdings LimitedFLIR is a registered trademark of FLIR Systems Inc andor its other trademarks trade names or company names referenced herein are used for identification only and are the property oftheir respective ownersThis product is protected by patents design patents patents pending or design patents pendingFair Use StatementYou may print no more than three copies of this manual for your own use You may not make any further copies or distribute or use themanual in any other way including without limitation exploiting the manual commercially or giving or selling copies to third 2010 Raymarine UK Ltd All rights number 870682Date 1 Important information 7 Chapter 6 Technical specification 29EMC installation guidelines 7 61 Technical specification 30Suppression ferrites 8 Chapter 7 Spare parts 31Connections to other equipment 8 71 GVM400 video module spares 32Product disposal 8IMO and SOLAS 8Technical accuracy 8GSeries handbooks 9Chapter 2 Planning the installation 1121 Parts supplied 1222 Power cables 1223 Entertainment system example 1324 Dimensions 15Chapter 3 Cables and connections 1731 GVM video module connections 1832 Thermal camera connection 20Chapter 4 Location and mounting 2341 Location requirements 2442 Mounting arrangement 24Chapter 5 2551 Video 26 56 GVM400 Installation 1 Important information Warning Switch off power supply Warning Product installation and Ensure the boats power supply is switched OFF before starting to install this product Do NOT connect operation or disconnect equipment with the power switched on This product must be installed and operated in unless instructed in this document accordance with the instructions provided Failure to do so could result in personal injury damage to your boat andor poor product performance EMC installation guidelines Warning Potential ignition source Raymarine equipment and accessories conform to the appropriate Compatibility EMC regulations to minimize This product is NOT approved for use in interference between equipment and minimize the atmospheres Do NOT install in effect such interference could have on the performance of your a atmosphere such as in an system engine room or near fuel tanks Correct installation is required to ensure that EMC performance is not compromised Warning High voltages For optimum EMC performance we recommend that wherever This product contains high voltages Do NOT remove possible any covers or otherwise attempt to access internal Raymarine equipment and cables connected to it are components unless specifically instructed in this document At least 1 m 3 ft from any equipment transmitting or cables carrying radio signals eg VHF radios cables and antennas In the case of SSB radios the distance should be increased Warning Product grounding to 7 ft 2 m Before applying power to this product ensure it has More than 2 m 7 ft from the path of a radar beam A radar been correctly grounded in accordance with the beam can normally be assumed to spread 20 degrees above instructions in this guide and below the radiating element The product is supplied from a separate battery from that used for engine start This is important to prevent erratic behavior and data loss which can occur if the engine start does not have a separate battery Raymarine specified cables are usedImportant information 7 Cables are not cut or extended unless doing so is detailed in Product disposal the installation manual Dispose of this product in accordance with the WEEE Directive Note Where constraints on the installation prevent any of the above always ensure the maximum possible separation between different items of electrical equipment to provide the best conditions for EMC performance The Waste Electrical and Electronic Equipment WEEE throughout the installation Directive requires the recycling of waste electrical and electronic equipment Whilst the WEEE Directive does not apply to some Raymarine products we support its policy and ask you to be aware of how to dispose of this cables may be fitted with suppression ferrites Theseare important for correct EMC performance If a ferrite has to be IMO and SOLASremoved for any purpose eg installation or maintenance it mustbe replaced in the original position before the product is used The equipment described within this document is intended for use on leisure marine boats and workboats not covered by only ferrites of the correct type supplied by Raymarine Maritime Organization IMO and Safety of Life at Sea dealers Carriage to other equipment Technical for ferrites on nonRaymarine cables To the best of our knowledge the information in this document wasIf your Raymarine equipment is to be connected to other equipment correct at the time it was produced However Raymarine cannotusing a cable not supplied by Raymarine a suppression ferrite accept liability for any inaccuracies or omissions it may contain InMUST always be attached to the cable near the Raymarine unit addition our policy of continuous product improvement may change specifications without notice As a result Raymarine cannot accept liability for any differences between the product and this document8 GVM400 Installation handbooksThe GSeries system has the following handbooks handbooks Description Part number GSeries system installation and 87070 commissioning instructions GSeries system operating instructions 86126 quick reference GSeries system user reference 81276 handbook Glass Bridge monitors user guide 81324 GSeries compact keyboard 81316 GSeries command center keyboard handbooks Description Part number SeaTalkng reference manual 81300All documents are available to download as PDFs information 910 GVM400 Installation 2 Planning the contents 21 Parts supplied on page 12 22 Power cables on page 12 23 Entertainment system example on page 13 24 Dimensions on page 15Planning the installation 1121 Parts supplied 22 Power cables GVM video module power cable requirements The GVM video module is not supplied with a power cable Power cables must be of the appropriate gauge 2 Power supply Cable gauge Cable gauge Cable length voltage AWM mm2 0 to 5 m 0 to 164 12 volts 20 052 1 ft 24 volts 20 052 5 to 10 m 164 to 12 volts 20 052 328 ft 24 volts 20 052 10 to 15 m 328 12 volts 20 052 to 492 ft 24 volts 20 052 15 to 20 m 492 12 volts 18 082 to 656 ft 24 volts 20 052 3 4 D1179711 GVM400 video module2 Installation instructions3 15 m 49 ft SVideo cable4 15 m 49 ft Audio cable12 GVM400 Installation instructions23 Entertainment system example 4 Audio SVideo 12 1 9 8 5 2 1 2 ABC 3 DEF 6 3 4 5 6 WPTS GHI JKL MNO PAGE MENU OUT MOB RANGE ENTER 7 8 9 IN PQRS TUV WXYZ ACTIVE DATA 0 DODGE STANDBY PILOT OK CANCEL AV SeaTalkng AV 10 SeaTalkng DVI VGA 7 SeaTalkng Audio 11 SeaTalkhs SeaTalkhs SVideo the installation 131 Television2 Wireless keyboard charge point3 Wireless keyboard4 Satellite TV5 Wireless base station6 Video camera7 Video camera with audio connection8 GVM video module9 SeaTalkhs switch10 GPM processor unit11 Audio output to vessels audio system12 SeaTalkng backbone14 GVM400 Installation instructions24 Dimensions 56 mm 22 in 170 mm 67 in 237 mm 933 in the installation 1516 GVM400 Installation 3 Cables and contents 31 GVM video module connections on page 18 32 Thermal camera connection on page 20Cables and connections 1731 GVM video module connections 1 2 SeaTalkhs 7 4 5 3 8 6 D11820118 GVM400 Installation instructions1 GVM video module Audio cables2 SeaTalkhs switch Cables for connecting audio to the GSeries system3 GSeries and SeaTalkhs devices Cable Part number Notes4 SVideo source for example video camera 15 m 49 ft stereo R08275 Supplied with the GVM5 SVideo connection using the supplied R08274 SVideo audio cable video module adaptor cable 3 m 98 ft stereo audio R08266 Supplied with the GPM6 Stereo audio connection using the supplied R08275 audio cable processor unit cable Only the SVideo and Composite 4 inputs support an 15 m 492 ft stereo R08298 associated audio connection audio cable7 Composite video source for example video camera8 Illustration showing the labels for the video and audio connections on the GVM video module Note Each GVM400 video module supports 1 SVideo input or 4 composite video inputs reduced to 3 composite video inputs if using SVideo input If a thermal camera is connected to a GVM video module no further video devices may be connected to that GVM unit The GSeries system supports a maximum of 3 GVM video modules providing a total of 12 video inputs less if connecting SVideo or thermal camera devicesVideo cablesCables for connecting video sources to the GSeries system Cable Part number Notes 15 m 49 ft SVideo R08274 Supplied with the GVM adaptor cable video module Note Refer to your dealer for suitable cables for connecting composite video sources to the GSeries and also for connecting SVideo sources to the adaptor cable listed aboveCables and connections 1932 Thermal camera connection 1 2You can connect a thermal camera to your systemThe camera is connected via a SeaTalkhs switch If you want touse the optional Joystick Control Unit JCU with the camera thismust also be connected to the SeaTalkhs switch A composite is also required between the camera and a GVM videomodule SeaTalkhs SeaTalkhs SeaTalkhs SeaTalkhs 8 7 4 3 6 5 D119351 1 GPM processor unit 2 SeaTalkhs switch20 GVM400 Installation instructions3 PoE Power over Ethernet injector only required if using the dealer or the Raymarine website for latest optional JCU software versions4 Joystick Control Unit JCU optional For further information regarding the cameras installation including connections and mounting refer to the installation5 Cable coupler instructions that accompany the camera6 Thermal camera7 Video connection Thermal camera cables Cabling requirements for thermal cameras8 GVM video module Camera to SeaTalkhs notes You will need a SeaTalkhs patch cable to connect the camera to the You can control the thermal camera using your GSeries SeaTalkhs switch The connection is made between the camera keyboard The Joystick Control Unit JCU is optional but can cable tail to the switch via the coupler supplied with the camera be used in conjunction with the GSeries system to control the Patch cables are available in a variety of lengths thermal camera if required Joystick Control Unit JCU You can only connect 1 thermal camera to each GVM video An Ethernet with power cable is used to connect the JCU The JCU module in your GSeries system When a thermal camera is is supplied with a 15 m 5 ft Ethernet cable for this connection if connected each GVM video module is limited to that input you require a different length contact your dealer for suitable cables only and does NOT support the connection of any further video devices Power over Ethernet PoE injector to SeaTalkhs switch Each thermal camera must be connected to Video Input 1 of a A SeaTalkhs patch cable is required for connecting the PoE injector GVM video module to the SeaTalkhs switch SeaTalkhs patch cables are available in a variety of lengths Dual payload thermal cameras include 2 independent lenses 1 for thermal infrared and visible light 1 for thermal infrared Video cables only These cameras include 2 separate video connections If Contact your dealer for suitable cables and adaptors you only have 1 GVM video module you should only connect the video cable labelled VIS IR visible light infrared in order to be able to switch between the 2 lenses If you have 2 or more Configuring the GVM video module for a GVM video modules you should connect the video cable labelled thermal camera VIS IR to GVM video module 1 and the video cable labelled If you want to view and control a thermal camera with your GSeries IR to GVM video module 2 system you must configure the GVM video module using the Thermal camera support requires the latest GSeries software To thermal camera application check your software version select MENU System Diagnostics In the thermal camera application Software Services Unit Info App Version Refer to your 1 Press the MENU buttonCables and connections 212 Select Thermal Camera Setup3 Select the Select GVM menu item A list of all connected GVM video modules is displayed along with serial numbers4 Select the GVM video module that the thermal camera is connected to5 Repeat Steps 1 to 4 for each GVM video module in your system that has a thermal camera connected to it Note You can only connect 1 thermal camera to each GVM video module in your GSeries system When a thermal camera is connected each GVM video module is limited to that input only and does NOT support the connection of any further video devices22 GVM400 Installation 4 Location and contents 41 Location requirements on page 24 42 Mounting arrangement on page 24Location and mounting 2341 Location requirements 42 Mounting selecting a location for the unit it is important to consider anumber of factors Do NOT install near sources of heat or vibration for example an engine Install below decks in a dry area Must be mounted on a vertical surface Sides and top must be level24 GVM400 Installation 5 contents 51 Video on page 2551 Video with video and their possible causes and solutions are described here Problem Possible causes Possible solutions Video picture is unavailable at some or all Video signal is not reaching the GVM Check the video source equipment Nav Stations video module Check the video connections to the GVM video module GVM video module or power supply Check the GVM video module status LEDs problem Check the GVM video module power supply SeaTalkhs network problem Check that all GVM video module and all GPM processor units are connected to the SeaTalkhs switch Check the status of the SeaTalkhs switch Check that SeaTalkhs cables are free from damage Software mismatch between equipment Contact Raymarine technical support may prevent communication Only Video Input 1 on the GVM video The GVM video module has been If you no longer want to connect a thermal camera to the GVM video module module is working previously connected to a thermal you must reset the GVM before you can use its other inputs To reset in the camera video application select MENU Video Setup Reset GVMGVM video module LED indications LED state Possible causesLED indications associated with the GVM video module are 2 flashing amber LEDs No network cable here 3 flashing amber LEDs Other network error LED state Possible causes Flashing 750 250 ms LEDs Retrieving software from memory 1 flashing various rates green LED Normal operation Heartbeat alternating between amber and red card This condition remains until a valid application is available from the 1 steady amber LED Power on memory card Lamp test 1 flashing red LED Unit can no longer poll input status 1 flashing amber LED Data acquisition failure26 GVM400 Installation instructions LED state Possible causes 4 flashing red LEDs Flash write error 6 flashing red LEDs Video stopped 7 flashing red LEDs Video error 8 flashing red LEDs possibly followed Hardware read failure by flashing 2728 GVM400 Installation 6 Technical contents 61 Technical specification on page 30Technical specification 2961 Technical specification Storage conditions for packaged unit Temperature 25 C to 55 C 13 F to 131 F Nominal supply voltage 12 or 24 V dc Relative humidity 75 Operating voltage range 107 to 32 V dc Dimensions Width 237 mm 933 in Fuse Breakers 12 V supply Height 170 mm 669 in 2 A fuse protection at distribution Depth 56 mm 220 in panel Weight 08 kg 176 lb 12 A thermal circuit breaker protection at distribution panel Data connections SeaTalkhs 24 V supply Video inputs Inputs 1 to 3 1 A fuse protection at distribution Composite video PAL 626 lines panel NTSC 525 lines 1 A thermal circuit breaker Input 4 protection at distribution panel SVideo or composite video Typical power consumption 650 mA at 12 V Audio input Stereo line in rated 1 V RMS 330 mA at 24 V associated with video input 4 only Environmental Installation environment SVideo or composite Operating temperature 15 C to Conformance 89336EEC as amended by 55 C 5 F to 131 F 9231EEC Nonoperating temperature 25 C EN609452002 to 70 C 13 F to 158 F Relative humidity limit 80 Water protection drip resistant when mounted vertically30 GVM400 Installation 7 Spare partsChapter contents 71 GVM400 video module spares on page 32Spare parts 3171 GVM400 video module sparesThe following parts are available as spares Cable Part number Notes GVM Connector Cover R08276 GVM install pack R0831832 GVM400 Installation ym a rin e c o m


NOTICE: Some pages have affiliate links to Amazon. As an Amazon Associate, I earn from qualifying purchases. Please read website Cookie, Privacy, and Disclamers by clicking HERE. To contact me click HERE. For my YouTube page click HERE