Raymarine G Series Keyboard Installation Guide 87084 1
Some manual pages may be blank. There will be an End of File notice after the last page.
Previous Page    Next Page
Go to page number
PDF to Text.
GSeries Command Center Electrical and Electronic Equipment DirectiveThe Waste Electrical and Electronic Equipment WEEEive requiresthe recycling of waste electrical and electronic equipment Whilst the WEEEDirective does not apply to some of Raymarines products we support itspolicy and ask you to be aware of how to dispose of this productThe crossed out wheelie bin symbol illustrated above and found on ourproducts signifies that this product should not be disposed of in generalwaste or landfillPlease contact your local dealer national distributor or Raymarine for information on product disposal DisclaimerThe technical and graphical information contained in this document to the best of ourknowledge was correct as it went to press However our policy of continuous improvement and updating may change product specifications without prior notice As a differences between the product and handbook may occur from time totime Raymarine cannot accept responsibility for any inaccuracies or omissions it maycontain For the latest product information visit our website installation equipment and accessories conform to the appropriate EMClations This minimizes interference which could otherwise affect the performance of your systemCorrect installation is required to ensure that EMC performance is not compromisedFor optimum EMC performance we recommend thatRaymarine equipment and the cables connected to it areiAt least 3 ft 1 m from any equipment transmitting or cables carrying radio signals eg VHF radios cables and antennas In the case of SSB radios the distance should be increased to 7 ft 2 miiMore than 7 ft 2 m from the path of a radar beam A radar beam can normally be assumed to spread 20 degrees above and below the radiating specified cables are usedCables are not cut or extendedAlways allow the maximum separation possible between different items of This will provide the best conditions for EMC performance for equipment must be installed and operated in accordance with the Raymarine instructions provided Failure to do so could result in poor product performance personal injury andor damage to your boatService and product contains no user serviceable components Please refer all maintenance and repair to authorized Raymarine repair may affect your warrantyUltra violet lightTo provide protection against the damaging effects of ultra violet UV light the sun cover should be placed on the unit when not in useDO NOT use acid ammonia based or abrasive productsDO NOT use commercial high pressure washing jet washDocument number 870841Date July conforms toFCC conforms toAdditional EN3004402CFR47 PART x 98 x 46Weight065 kgMountingDash mountHandheld with optional wireless upgradeSupply voltage9 V to 16 VPower consumption15 WEnvironmental temperature 15C to 55C 5F to temperature 25C to 70C 13F to158Frelative humidity limit 95water to CFR46 conditions 25C to 55C 13F to 158Frelatiive humidity plcAnchorage PO3 5TDUnited KingdomTel 44 069 3611Fax 44 0 4642Raymarine Inc21 Manchester Hampshire 030544801Tel 1 6038815200Fax 1 Keyboard is installed as a part of the Raymarine GSeriesmarine electronics systemRefer to the additional documentation supplied with your GseriesGPM400 processor for additional information necessary to installthe keyboard within your systemAll documents can be downloaded of KeyboardsThe GSeries system will support up to 8 system T NoGSeries command center coverR083071 m 33 ftalkNMEA2000 cableA06039400 mm 1575 inSeaTalk backbone Tpiece cover mounting numberGSeries system installation and commissioning Series system operating system user reference GSeries Keyboard communicates using the SeaTalkng system It may be connected directly to the backbone wiredused remotely with a separate basestation and wireless upgrade kitYou should have at least one permanently wired keyboard In the event that any wireless keyboards are lost the wired keyboard can be used to control the diagramWhen connecting a keyboard to the system record its details on your diagram You will need this information during commissioning Refer to the separate GSeries system installation instructions for sample connection NumberKeyboard to SeaTalk400 mm 1575 inSeaTalk spur cableA060381 m 33 ftSeaTalk spur with the keyboard3 m 98 ftSeaTalk spur cableA060405 m 164 ftSeaTalk spur and environmentThe keyboard is suitable for mounting both above and below to CFR46 standardUse the cutting template provided within this bookletConnect cable into keyboard before clamping in placeThe following conditions applyDo NOT install near sources of heat eg engineInstall the unit well away from potential sources of bend radius of 100 mm 394 inSeaTalk NG
NOTICE: Some pages have affiliate links to Amazon. As an Amazon Associate, I earn from qualifying purchases. Please read website Cookie, Privacy, and Disclamers by clicking HERE. To contact me click HERE. For my YouTube page click HERE