Thursday, November14, 2019 L-36.com

Raymarine Rs125 Gps Installation Instructions 81247 4



Note:

This is the new page for displaying documents. It allows documents to display on devices without pdf viewers specifically mobile devices, a new Google requirement. Note also that some documents have blank pages. Just click on "Next Page" if that happens.
Previous Page    Next Page Go to page number Note: Page number may not agree with index page numbers


Previous Page    Next Page
Go to page number
Note: Page number may not agree with index page numbers

PDF to Text.

Raystar 125 GPS Receiver                                                                                       1
Owner's Handbook                                                                    www.raymarine.com


Welcome to the Raystar RS125 GPS Receiver

                                            Your handbook contains an explanation of how to install,
                                            operate and maintain your Raystar RS125 GPS Receiver.

                                            Intended Use
                                            This product is a GPS antenna with a built-in position
                                            fixing receiver using either NMEA0183 (Version 2.3 or
                                            later), or Raymarine SeaTalk data output. The intended
                                            application is for leisure marine boats and workboats not
                                            covered by IMO/SOLAS carriage requirements.


What's in the box?....




        Part No: R38103                                                           Part No: R38104
   Raystar RS125 GPS Receiver                                                 10m (33ft) NMEA/SeaTalk
                                                                                 connection cable
                                             Part No: E35018
                                              Pole mount kit




                                                                             Thumb nuts (x2)
                                                                                                      3- way
       Flush mount gasket                                                                           Scotchlok TM
                                                                                                  connectors (x5)
                                                                Studs (x2)     Screws (x2)
The Raystar RS125 GPS Receiver has no user serviceable parts.


What tools do I need to install it?....



            Drill            6mm (1/4 in)              20mm (13/16 in)              Phillips
                             Drill bit                 Drill bit                    screwdriver      Adhesive tape
                                                                                                                     D7471_2
2    Safety notices                                                 RS125 GPS Receiver
WARNING: Navigation aid
Although this product has been designed to be accurate and reliable, many factors
can affect its performance. As a result, it should only be used as an aid to navigation
and should never replace common sense and navigational judgement. Always
maintain a permanent watch so you can respond to situations as they develop.
WARNING: Product installation
This equipment must be installed and operated in accordance with the instructions
contained in this handbook. Failure to do so could result in poor product
performance, personal injury and/or damage to your boat.
WARNING: Electrical safety
Make sure the power supply is switched off before you make any electrical
connections.
WARNING: Lithium battery
This unit has a lithium battery fitted. DO NOT attempt to recharge this battery. DO
NOT incinerate this battery. Ensure you follow local regulations when disposing of
this unit.


Where can I install the unit?....


                Pole                             Rail                               Flush
                mount                            mount                              mount




                        Radar
          Above the beam
                                                                       No trip
                                In the                                 or tread
                                beam
                                                         Top of
                                                         the mast
          Below the beam




               Clear view of the sky               VHF Radio and other antenna
                                                             Minimum 1.0 m (3 ft)
                                                                                            D7472_2
To mount the unit on a pole....                                                                  3

                                  1 Securely attach the pole mount base to a
                                    suitable pole.
                                  2 Pass the cable and connector through either
                                     a the center of the pole mount bracket and
                                         the pole, or
                              3
                                     b the cable exit hole alongside the center
                                         hole.
                                  3 Attach the connector securely to the plug in
                                    the base of the unit.
                              2
                                  4 Secure the receiver to the pole mount base
                                    using the screws provided.




1
                                  Notes:
                                  1. To mount the receiver on a pole, you will
                                     need a pole of suitable length with a 1 inch
                              a      14 TPI thread not exceeding 20mm in
                                     length.
                                  2. To rail mount the receiver you will need to
b                             4      purchase a suitable rail mount bracket.



To flush mount the unit....

                                  1 Use the template supplied in this handbook to
                                      mark the two fixing holes and the center hole.
                                  2   Drill the holes using the drill sizes shown on
                                      the template.
                                  3   Screw the two fixing studs into the underside
                              5       of the receiver unit.
3                                 4   Place the waterproof gasket into position on
                                      the underside of the receiver.
                                  5   Attach the connector securely to the plug in
                                      the base of the unit and pass the cable
                                      through the center hole on the mounting
4
                                      surface.
                                  6   Carefully position the receiver so that the
                                      mounting studs pass through the holes in the
                                      mounting surface.
                                  7   Secure the receiver to the mounting surface
                                      using the two thumb nuts (these should be
                              7       hand-tight only).
                                                                                       D7473_3
To connect the RS125 using Scotchlok connectors....
4                                                                       RS125 GPS Receiver
                                          1 Using suitable wire clippers, remove the tinned
                                            ends from the individual cables. Leave the
                                            insulation intact.
                                          2 Place the wires to be joined into the connectors,
                                            ensuring correct polarity and that the wires are
                                            fully pushed home.
                                          3 Using a pair of pliers, crimp the connector bulb
                                            together ensuring that a secure connection has
                                            been made.
                                          4 Ensure the cables are secured in a suitable
                                            position to prevent the joint being placed under
                                            strain.


To connect to NMEA 0183....

                                                        Red (12 - 32 V /+)
                                                        Yellow (NMEA out /+)
                                                        Brown (RTCM in /+)
                                                        Green (NMEA in /+)
                                                        Shield (0V/ ground / -)
NMEA sentences
Output sentences:
    GPGGA, GPGSA, GPGSV, GPGLL, GPRMC, GPDTM, GPGNS, GPVTG, PRAYA
Input sentences:
    PRAYI, PRAYE, PRAYA
Note: If the Brown (RTCM) and Green (NMEA in/+) wires are not used, they must be
suitably grounded.
If you do not have a breaker in the power circuit, an in-line 0.5 A quick blow fuse should be
fitted to the positive (red) lead of the cable.

To connect to SeaTalk....

                                                        Red (12 V /+)
                                                        Yellow (SeaTalk input/output / +)
                                                        Brown (RTCM in / +)
                                                        Green (connect with Red 12V wire/ +)
                                                        Shield (0 V/ground / -)

Note: If the Brown (RTCM) wire is not used, it must be suitably grounded to 0 Volts.
If you do not have a breaker in the power circuit, an in-line 0.5 A quick blow fuse should be
fitted to the positive (red) lead of the cable.
                                                                                                D7474_2
To connect to the RS125 into a SeaTalk system....                                                    5

C-Series



         RS125 GPS                                                     C-Series SeaTalk cable
         Receiver cable                                                Part No. R08050

                                                     Scotchlok connectors
E-Series




          RS125 GPS                                                    E-Series SeaTalk cable
          Receiver cable          To external                          Part No. E55054
                                       alarm
To connect to an E-Series display using SeaTalk....
When connecting your RS125 into an existing SeaTalk network it should be powered from
the network and not the display. The yellow (data) cable should be connected to your C or
E-Series display.
If you are not using a land-based DGPS antenna on your RS125 GPS receiver (most
installations do not), you should connect the brown RTCM input to the shield wire (ground).
This will prevent outside RF energy from inadvertently injecting noise into the system.

To connect to a Personal Computer using NMEA

                                            Scotchlok connectors




                                 + 12 V

RS125 GPS
Receiver cable

                                                                                9-pin Serial Cable
                                                                                 Part No. E86001
                                          0V

If you are connecting your RS 125 GPS receiver to a PC, you will need a Serial Data Cable,
Part No. E86001. Connect the Yellow from the RS 125 to the Yellow of the Serial Data
Cable. Connect the Red from the RS 125 to the positive of your boat's 12 V DC power
supply. Connect the Brown, Green and Shield from the RS 125 and a Black from the Serial
Data Cable to your boat's ground.
                                                                                                         D7918_1
What
6    do the lights mean?....                                           RS125 GPS Receiver


                                          Flashing RED
                                          Unit is in bootcode, either being upgraded
                                          or unable to boot.
                                          Flashing ORANGE
                                          Unit is running, but does not have a fix.
                                          Flashing GREEN
                                          Unit is running and has a fix.
                                          1 flash every 2 seconds indicates NMEA connection.
                                          1 flash every 4 seconds indicates SeaTalk connection.


SOG/COG filter....

The integral SOG/COG filter fitted to your RS125 compensates for the oscillating motion of
your boat to give a clearer indication of the boat's course and speed.
Slow moving boats, or boats sailing in rough seas will benefit from a high filter setting,
whereas a powerboat that can quickly change speed and direction will benefit from a low
setting.
The default setting for your RS125 is MEDIUM.
Adjustment of the SOG/COG filter is made from your system display.
For full details of how to adjust the SOG/COG filter refer to the relevant Manufacturer's
manual.

Accessories....

You can obtain the following accessories to help you quickly and easily connect your RS125
to existing equipment:

E36013 - 600mm Antenna conversion cable
                                                The antenna conversion cable enables you to
                                                connect your RS125 receiver to an existing
                                                RS120, RS112 or RS114 cable, saving the time
                                                and trouble of running a new cable.

E36014 - 1000mm Display conversion cable
                                     The display conversion cable enables you to
                                     quickly connect your RS125 receiver to an
                                     existing RC425 or RC420 display, saving time
                                     and trouble.
                                                                                                  D7687_2
Important Information                                                                       7

EMC conformance
All Raymarine equipment and accessories are designed to the best industry standards for use
in the recreational marine environment. The design and manufacture of Raymarine
equipment and accessories conforms to the appropriate Electromagnetic Compatibility (EMC)
standards, but correct installation is required to ensure that performance is not compromised.
For full details and installation guidelines refer to or web site at www.raymarine.com
Declaration of conformity
We, Raymarine Limited, Quay Point, Portsmouth, Hampshire, England PO6 3TD declare, under
our sole responsibility, that the product identified in this declaration, and to which this
declaration relates, is in conformity with the essential requirements of European Parliament
and Council Directive 1999/5/EC on radio equipment and on telecommunication terminal
equipment and the mutual recognition of their conformity.
       Product name: Raystar 125 GPS Receiver
       Product number: E32042
This product has been assessed to Conformity Procedure Annex IV of the Directive. The
assessment is consistent with a Technical Construction File showing conformity with the
essential requirements of the Directive and has been reviewed by Notified Body No.0191.
Signed:                     A. Abbas, International Compliance Manager. Raymarine Ltd.
                            21st January 2005
CE conformity
This product is labeled with the CE conformity mark:       0191
SiRF Technology Inc.
This product uses certain elements of software supplied to Raymarine by
SiRF Technologies Inc.
For full details of their licensing agreement refer to our website at www.raymarine.com
Warranty
To register your new Raymarine product, please take a few minutes to fill out the warranty
card.
It is important that you complete the owner information and return the card to us to receive
full warranty benefits.
Your product can also be registered via our web site www.raymarine.com
Handbook information
To the best of our knowledge, the information contained in this hadbook was correct as it
wento press. Raymarine cannot accept any liability for any inaccuracies or ommissions it may
contain.
In addition, our policy of continuous product improvement may change specifications
without notice. As a result, Raymarine cannot accept liability for any differences between the
product anthe handbook.
                                                                                                 D7476_2
 To
 8
To  get
   get   Technical
       Technical     Support....
                 Support....                                                   RS125 GPS Receiver


          www.raymarine.com
         www.raymarine.com
           United
          United  States
                 States                                      Europe
                                                            Europe

            Raymarine
          Raymarine      Technical
                        Technical   Support
                                   Support                   Technical
                                                            Technical  Support
                                                                      Support
            1-800-539-5539
          1-800-539-5539    extension
                          extension   2444,
                                    2444, oror               Services
                                                            Services
            (603)
          (603)   -881-5200
                -881-5200                                    Accessories
                                                            Accessories

           Product
          Product    Repair
                   Repair     and
                            and      Service
                                   Service                   Raymarine
                                                            Raymarine  UK
                                                                      UK   Limited
                                                                         Limited
           Raymarine
          Raymarine   Product
                    Product    Repair
                             Repair    Center
                                      Center                 Anchorage
                                                            Anchorage  Park
                                                                      Park
           21
          21  Manchester
             Manchester   Street,
                         Street,                             Portsmouth
                                                            Portsmouth
           Merrimack,
          Merrimack,  NH
                     NH    03054
                         03054     - 4801
                                 - 4801                      PO3
                                                            PO3   5TD
                                                                 5TD
           1-800-539-5539
          1-800-539-5539                                     England
                                                            England

           Opening
          Opening    hours:
                   hours:                           Tel:
                                                   Tel:
           Monday
          Monday     through
                   through    Friday
                            Friday   0815
                                    0815  - 1700    +44(0)23
                                            - 1700 +44(0)23  9271
                                                            9271  4713
                                                                 4713
           Eastern
          Eastern   Standard
                  Standard  oror  Eastern
                                Eastern   Daylight
                                        Daylight
           Savings
          Savings   Time.
                  Time.                             Fax:
                                                   Fax:
                                                    +44(0)23
                                                   +44(0)23  92661228
                                                            9266   1228




           Help us to help you
           When requesting service, please quote the following product information:
           Equipment type Model number Serial number

 Waste Electrical and Electronic Equipment Directive....

           The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste
           electrical and electronic equipment. Whilst the WEEE Directive does not apply to some of
           Raymarine's products, we support its policy and ask you to be aware of how to dispose of this
           product.
The crossed
        Helpoutus
                wheelie
                  to helpbin symbol,
                              you illustrated above, and found on our products signifies that this
product should not be disposed of in general waste or landfill.
        When requesting service, please quote the following product information:
Please contact your local dealer, national distributor or Raymarine Technical Services for information on
                                                                                                                D7477_2




product Equipment
        disposal. type        Model number Serial number
                                                                                                              D7477_1




   Raymarine
 Raymarine       UKUK  Limited
                     Limited            Raymarine
                                      Raymarine      Incorporated
                                                   Incorporated
   Quay
 Quay     Point,
        Point,   Northarbour
               Northarbour    Road,
                            Road,     2121  Manchester
                                          Manchester   Street,
                                                     Street,                         Document No: 81247_4
   Portsmouth,
 Portsmouth,      Hampshire
                Hampshire               Merrimack,
                                      Merrimack,   NH
                                                  NH   03054
                                                     03054     - 4801
                                                             - 4801
   England
 England     PO6
           PO6     3TD
                 3TD                    USA
                                      USA                                              Raymarine April 2006
                                                                                     Document No: 81247_3
   Tel:
 Tel: ++ 4444  (0)23
            (0)23    9269
                   9269    3611
                         3611           Tel:
                                      Tel:   603-881-5200
                                           603-881-5200                              Date: April 2005
   Fax:
 Fax: ++ 4444  (0)23
            (0)23    9269
                   9269    4642
                        4642            Fax:
                                      Fax:   603-864-4756
                                           603-864-4756
   www.raymarine.com
 www.raymarine.com                      www.raymarine.com
                                      www.raymarine.com                                Raymarine 2005


Ad by Google

Disclaimer:
The information on this web site has not been checked for accuracy. It is for entertainment purposes only and should be independently verified before using for any other reason. There are five sources. 1) Documents and manuals from a variety of sources. These have not been checked for accuracy and in many cases have not even been read by anyone associated with L-36.com. I have no idea of they are useful or accurate, I leave that to the reader. 2) Articles others have written and submitted. If you have questions on these, please contact the author. 3) Articles that represent my personal opinions. These are intended to promote thought and for entertainment. These are not intended to be fact, they are my opinions. 4) Small programs that generate result presented on a web page. Like any computer program, these may and in some cases do have errors. Almost all of these also make simplifying assumptions so they are not totally accurate even if there are no errors. Please verify all results. 5) Weather information is from numerious of sources and is presented automatically. It is not checked for accuracy either by anyone at L-36.com or by the source which is typically the US Government. See the NOAA web site for their disclaimer. Finally, tide and current data on this site is from 2007 and 2008 data bases, which may contain even older data. Changes in harbors due to building or dredging change tides and currents and for that reason many of the locations presented are no longer supported by newer data bases. For example, there is very little tidal current data in newer data bases so current data is likely wrong to some extent. This data is NOT FOR NAVIGATION. See the XTide disclaimer for details. In addition, tide and current are influenced by storms, river flow, and other factors beyond the ability of any predictive program.