Dimensions of Tempest

Updated 10/25/2012

Selected Measurements for Tempest

BOAT	I	J	P	E	ISP	JSP	PY	EY	Disp	LWL	DRAFT
Tempest	19.7	7.5	25	11.1	0	0	0	0	0	0	0

Links to our Multi Vendor Used Sail Directory for Tempest

Other Data Base Entries for tempest*

Click on boat nane to use

BOAT	I	J	P	E	ISP	SPL	PY	PE	LWL	DRAFT	DISP
International Tempest	21.25	6.75	25	11.08					19		1010
O'DAY 23 TEMPEST	25.5	8.6	23	10
O'DAY 23.2 TEMPEST	26.1	8.7	23.2	9.5
O'DAY 23.2 TEMPEST	26.5	8.4	23	10
O'DAY TEMPEST	26.5	8.4	23	10	26.5	8.4
Oday Tempest 23	26.5	8.4	23	10					17	3.8	3000
TEMPEST	19.7	7.5	25	11.1
TEMPEST 23 (O'DAY)	26.5	8.4	23	10					17	3.67	3000

Click Here for other boat types or to check dimensions from other data bases. We now offer three data bases.

Sail Area Calculations

BOAT	I	J	P	E	ISP	JSP	PY	EY	Disp	LWL	DRAFT
Tempest	19.7	7.5	25	11.1	19.7	7.5	0	0	0	0	0

The following formulas are approximate
Sail areas depend on lots of factors, leach hollow, foot round, luff hollow etc. Also, remember that jib sail area in general is based on the forestay length, I. But all things considered, these numbers are close but should not be considered exact. They are rules of thumb, not measurements of a this specific boat.

Mainsail

Mainsail = (P x E) / 2 = 139 sq ft
Racing Mainsail (add 10%) = 153 sq ft

Genoa

155% Genoa = (( J x I ) / 2) x 1.65 = 122 sq ft
135% Genoa = (( J x I ) / 2) x 1.44 = 106 sq ft

Jib

	_______
LP of full fore triangle = ( I x J ) / √	I² + J² = 7

Jib size to fill fore triangle = 93%
100% Jib = ( I x J ) / 2 = 74 sq ft

A more accurate LP calculator is HERE

Spinnaker

Spinnaker Area = Max Luff x Max Girth x ( 70-85%) = 189 to 230 sq ft
"Square" Spinnaker Area = Max Luff x Max Girth) = 270 sq ft
AC Area = 225 sq ft
Maximum Luff (.95 * sqrt (JSP^2 + ISP^2) = 20.03 feet
Maximum Girth = 1.8 * JSP = 13.5 feet
Ref

DEFINITIONS

"P" is the luff length of the mainsail, measured along the aft face of the mast from the top of the boom to the highest point that the mainsail can be hoisted or black band.

"E" is the foot length of the mainsail, measured along the boom from the aft face of the mast to the outermost point on the boom to which the main can be pulled or to the black band.

"I" is measured along the front of mast from the genoa halyard to the main deck. The main deck is where the deck would be if there were no deckhouse.

"J" is the base of the foretriangle measured along the deck from the headstay pin to the front of the mast.

"JSP" is the length of the spinnaker pole or the distance from the forward end of the bowsprit (fully extended) to the front face of the mast.

"ISP" is measured from the highest spinnaker halyard to the deck.

"PY" and "EY" are, respectively the luff length and foot length of the mizzen of a yawl or ketch measured in the same way as for the mainsail.

"IY" is the measurement from the staysail halyard to the deck.

"JY" is the measurement from the staysail stay to the front face of the mast.

"LP" is the shortest distance between the clew and the luff of the genoa.

Data*

This data is supplied as a reference and all boat dimensions should be verified before using it in any critical application.
The information in these data bases is a starting point. There are errors as you can see as the different data bases do not always agree. In addition, some boats have been modified from stock and will not match the data in these databases. None of this data has been checked by L-36.com so please always check your boat before relying on this data.
Data is from a variety of sources.

db = SBD is used under the Creative Commons License sailboatdata.com (sailboatdata.com) / CC BY 3.0

db = PHRF is the PHRF Critical Dimensions database
db = WEB is the commonly available data found on many web sites
db = BIG is a combination of all of the above.

NOTICE: Some pages have affiliate links to Amazon. As an Amazon Associate, I earn from qualifying purchases. Please read website Cookie, Privacy, and Disclamers by clicking HERE. To contact me click HERE. For my YouTube page click HERE